Kiln schedule, the 8-12 percent band, case-hardening and why most joint failures in restaurant chairs are actually moisture failures.
Why the kiln is the most important room in the factory
Most seating failures blamed on joinery are actually moisture failures. Timber that leaves a kiln too wet shrinks after it is made into a frame, and the glue line opens. The joint was fine; the water content was not.
Restaurant seating is contract-grade, thick-sectioned and the largest single load on our kilns. Getting the schedule wrong here is expensive in a way it is not in a domestic category: the failure happens in a room full of customers.
We dry to 8 to 12 percent and meter every batch. The reading is recorded against the batch number and printed on the packing list, so it can be checked at destination.
Restaurants, cafés, bistros and hotel dining rooms — the largest category we build, 490 models. Stacking four to six high is common because rooms get re-set, and a stackable frame is a different engineering job from a knock-down one.
The schedule
A kiln charge runs 15 to 25 days depending on species and section thickness, stepping temperature up and humidity down in stages. Rushing it by raising temperature early produces case-hardening: the outside of the board dries and locks while the core is still wet, and the board moves later, inside a finished chair.
Contract sections run heavier than domestic: 45 to 55 mm legs, 25 to 30 mm rails, and a stretcher on the models that get dragged rather than lifted. The extra section is not for show — it is what survives a room being re-set several times a day.
Contract sections are thick, and with 490 models this category is most of what goes through the kiln. Thick stock dries slowly and checks if pushed, so the charge is grouped by section and the schedule is written to the thickest blank in it.
| Stage | Temperature | Duration | Purpose |
|---|---|---|---|
| Pre-heating | 40-50 °C, high humidity | 1-2 days | Warm the charge through |
| Main drying | 55-70 °C stepped | 10-18 days | Down to 12-14% |
| Equalising | 70-75 °C, low humidity | 2-4 days | Even out the core |
| Conditioning | Steam injection | 1-2 days | Relieve case-hardening |
| Cool and meter | Ambient | 1 day | Verify 8-12% before release |
Kiln schedule
Defects we reject for
End checking, collapse, honeycombing, sticker stain and fungal discolouration. Any of these disqualify a board from a frame component. They are cheap to reject at the kiln and expensive to discover after assembly. Restaurant Chairs use the same graded stock as every other model we build.
Finishes are specified for cleaning, not for depth of sheen. A restaurant seat is wiped with an alkaline agent several times a day, so the coating is chosen for chemical resistance, and the seat edges where the cloth catches are the first thing inspected.
Equilibrium, and what it means for your market
Timber settles at the moisture content the surrounding air dictates. A frame that arrives at 10 percent into a heated Nordic restaurant at 30 percent relative humidity will drop towards 6 percent and shrink as it does. That movement is normal and it is why we hold the band, seal end grain, and specify a joint that tolerates it.
A restaurant runs a humid kitchen and an air-conditioned dining room, often in the same building, and the seating sits at whatever the room dictates. Contract frames are therefore built on a joint that tolerates movement rather than one that resists it.
Species behave differently in the kiln
Ash — around 70% of what we run — dries steadily and holds its colour if the schedule is respected. Rubberwood, the other 30%, dries quickly and evenly and is the most forgiving charge in the yard. Oak is slow and prone to checking if pushed, and beech dries fast but collapses if the temperature goes up too early; both are custom runs for us. The schedule is written per species, not per thickness, and the two get confused constantly.
Ash carries most of this programme and rubberwood covers the rest, both bought to a specification that assumes contract service: ash where the frame takes a daily racking load, rubberwood where the price point has to work.
What restaurant chairs demand from the kiln
A restaurant chair is specified for turnover, not for comfort in the abstract. It gets sat in hard, dragged across a floor and wiped down several times a day. Frames are built to EN 16139 Level 2 and the seat is designed to survive cleaning, which rules out a lot of domestic construction.
Corner blocks glued and screwed, stretchers on the heavier models, and a seat rail section big enough to take a repeated racking load. The test regime cycles the frame far harder than a domestic standard does.
What happens after the kiln
Dried stock is held in a covered, conditioned store until it is machined. Leave it in an open yard through a Foshan wet season and it will take water back up within days, which undoes the schedule. This is the step most factories skip and the reason a moisture reading taken at packing matters more than one taken at the kiln.
We meter at both. If the two disagree, the charge goes back before it reaches the machining line.
This stock moves in volume and it is metered at packing as well as at the kiln, because a container of restaurant seating sits in a humid port before it is unloaded, and the reading at destination is the one that matters.
Two per carton, 0.10 to 0.15 m³, stackable or knock-down. MOQ is 6 pieces per model, and most buyers run two to four models in one container.
Which models this applies to
There are 486 models in this category: 85% run on a solid wood frame and 15% carry an upholstered or soft cover, so the moisture discipline applies to different components in different proportions.
Three of them as they stand today: A008 (100% Solid Wood, MOQ 6 pcs), XY-24018 (Solid wood, MOQ 6 pcs), A004 (Solid wood, MOQ 6 pcs).
What moisture damage looks like on restaurant chairs
Seats delaminating under daily wiping, stretchers loosening on models that get dragged rather than lifted, and finishes going dull where the cleaning agent is too alkaline. Ask what cleaner the operator uses.
EN 16139 Level 2 is the contract grade: higher cycle counts on seat and back, a leg forward load, and a stability test that assumes the user does not sit down gently. Reports are raised per model, not per range.
Reading a moisture meter properly
Take three readings along a blank and average them, and correct for timber temperature. Pin meters, not pinless ones — and the reading that counts is the one taken at packing, not the one taken at the kiln.
Reference
Questions
What moisture content do you ship at?
8 to 12 percent, metered per batch, with the reading recorded on the packing list.
Does the schedule change for this category?
Contract sections are thick, and with 490 models this category is most of what goes through the kiln. Thick stock dries slowly and checks if pushed, so the charge is grouped by section and the schedule is written to the thickest blank in it.
Can I specify a tighter band?
Yes - say the target on the order and the charge is scheduled to it.
Does the schedule change for restaurant chairs?
A restaurant chair is specified for turnover, not for comfort in the abstract. It gets sat in hard, dragged across a floor and wiped down several times a day. Frames are built to EN 16139 Level 2 and the seat is designed to survive cleaning, which rules out a lot of domestic construction.
What goes wrong on restaurant chairs if the moisture content is off?
Seats delaminating under daily wiping, stretchers loosening on models that get dragged rather than lifted, and finishes going dull where the cleaning agent is too alkaline. Ask what cleaner the operator uses.