Kiln schedule, the 8-12 percent band, case-hardening and why most joint failures in lounge chairs are actually moisture failures.
Why the kiln is the most important room in the factory
Most seating failures blamed on joinery are actually moisture failures. Timber that leaves a kiln too wet shrinks after it is made into a frame, and the glue line opens. The joint was fine; the water content was not.
Most lounge chairs are covered, which changes what moisture means here. The frame cannot crack where nobody sees it, but it can move inside the cover, and the symptom is a wrinkle or a split seam rather than a visible crack.
We dry to 8 to 12 percent and meter every batch. The reading is recorded against the batch number and printed on the packing list, so it can be checked at destination.
Hotel lobbies, waiting areas, senior living, reading corners. Seat height 400 to 430 mm with the back raked further than a dining chair, because the sitter is resting rather than eating. A side table at 350 to 400 mm goes with it.
The schedule
A kiln charge runs 15 to 25 days depending on species and section thickness, stepping temperature up and humidity down in stages. Rushing it by raising temperature early produces case-hardening: the outside of the board dries and locks while the core is still wet, and the board moves later, inside a finished chair.
The frame is a substrate for upholstery, so sections run lighter than a dining chair: 30 to 40 mm on the load-bearing rails, with a shaped ply or a webbed deck carrying the seat. Timber here is dried for stability rather than for appearance — most of it is never seen.
Upholstered frames are dried for stability rather than for looks: a rail that moves inside a cover shows as a wrinkle or a split seam instead of a crack, and it is far harder to diagnose afterwards. This stock is held to the tighter end of the band.
| Stage | Temperature | Duration | Purpose |
|---|---|---|---|
| Pre-heating | 40-50 °C, high humidity | 1-2 days | Warm the charge through |
| Main drying | 55-70 °C stepped | 10-18 days | Down to 12-14% |
| Equalising | 70-75 °C, low humidity | 2-4 days | Even out the core |
| Conditioning | Steam injection | 1-2 days | Relieve case-hardening |
| Cool and meter | Ambient | 1 day | Verify 8-12% before release |
Kiln schedule
Defects we reject for
End checking, collapse, honeycombing, sticker stain and fungal discolouration. Any of these disqualify a board from a frame component. They are cheap to reject at the kiln and expensive to discover after assembly. Wooden Lounge Chairs use the same graded stock as every other model we build.
Almost none of the frame shows. What matters is that nothing rough touches the cover from inside: a splinter on a rail wears through fabric from the back within months, which is why upholstered frames are sanded and sealed even where no one will look.
Equilibrium, and what it means for your market
Timber settles at the moisture content the surrounding air dictates. A frame that arrives at 10 percent into a heated Nordic restaurant at 30 percent relative humidity will drop towards 6 percent and shrink as it does. That movement is normal and it is why we hold the band, seal end grain, and specify a joint that tolerates it.
An upholstered frame is buffered: the cover and the foam slow the exchange with room air, so the frame moves more slowly than an exposed dining chair and it moves somewhere else. The risk is a seam that opens in month six, not a joint that opens in week one.
Species behave differently in the kiln
Ash — around 70% of what we run — dries steadily and holds its colour if the schedule is respected. Rubberwood, the other 30%, dries quickly and evenly and is the most forgiving charge in the yard. Oak is slow and prone to checking if pushed, and beech dries fast but collapses if the temperature goes up too early; both are custom runs for us. The schedule is written per species, not per thickness, and the two get confused constantly.
The timber here is mostly hidden, so the programme runs ash and rubberwood on cost and stability rather than on figure. In this category the species conversation is about the cover, not the frame.
What lounge chairs demand from the kiln
A lounge chair is a soft seat on a frame, not a frame with a pad. 220 of the 226 models in this category are upholstered, so the frame is a substrate: it has to hold the foam and the cover in shape under a sitter who stays put for an hour, not one who leaves in twenty minutes.
Frames are wood or metal under the cover, and the load path goes through the seat deck rather than the rails. Webbing or a sprung deck decides how the seat feels after a year more than the timber species does.
What happens after the kiln
Dried stock is held in a covered, conditioned store until it is machined. Leave it in an open yard through a Foshan wet season and it will take water back up within days, which undoes the schedule. This is the step most factories skip and the reason a moisture reading taken at packing matters more than one taken at the kiln.
We meter at both. If the two disagree, the charge goes back before it reaches the machining line.
Frames for upholstery go straight from the conditioned store to machining, because a frame that has picked up moisture will move after the cover is fitted — and a cover hides that movement until the seam splits.
The bulky end of the catalogue: 0.22 to 0.34 m³ per carton, one piece, fully assembled. Freight dominates the landed cost, which is why buyers consolidate them with flatter models. MOQ is 4 pieces, and 2 on some models.
Which models this applies to
There are 225 models in this category: 1% run on a solid wood frame and 99% carry an upholstered or soft cover, so the moisture discipline applies to different components in different proportions.
Three of them as they stand today: GDC-5652 (Velvet/Fabric/Leather, MOQ 2 pcs), GDC-5652 (Velvet/Fabric/Leather, MOQ 4 pcs), GDC-5652 (Velvet/Fabric/Leather, MOQ 4 pcs).
What moisture damage looks like on lounge chairs
Seats that bottom out, covers that pill at the front edge, and frames that creak because the deck was stapled rather than webbed. Comfort complaints are almost always foam density, not frame strength.
Comfort testing counts as much as strength here: foam compression set under repeated loading, cover abrasion, and a frame fatigue test at Level 1 or Level 2 depending on the traffic the lobby actually sees.
Reading a moisture meter properly
Take three readings along a blank and average them, and correct for timber temperature. Pin meters, not pinless ones — and the reading that counts is the one taken at packing, not the one taken at the kiln.
Reference
Questions
What moisture content do you ship at?
8 to 12 percent, metered per batch, with the reading recorded on the packing list.
Does the schedule change for this category?
Upholstered frames are dried for stability rather than for looks: a rail that moves inside a cover shows as a wrinkle or a split seam instead of a crack, and it is far harder to diagnose afterwards. This stock is held to the tighter end of the band.
Can I specify a tighter band?
Yes - say the target on the order and the charge is scheduled to it.
Does the schedule change for lounge chairs?
A lounge chair is a soft seat on a frame, not a frame with a pad. 220 of the 226 models in this category are upholstered, so the frame is a substrate: it has to hold the foam and the cover in shape under a sitter who stays put for an hour, not one who leaves in twenty minutes.
What goes wrong on lounge chairs if the moisture content is off?
Seats that bottom out, covers that pill at the front edge, and frames that creak because the deck was stapled rather than webbed. Comfort complaints are almost always foam density, not frame strength.