Kiln schedule, the 8-12 percent band, case-hardening and why most joint failures in dining chairs are actually moisture failures.
Why the kiln is the most important room in the factory
Most seating failures blamed on joinery are actually moisture failures. Timber that leaves a kiln too wet shrinks after it is made into a frame, and the glue line opens. The joint was fine; the water content was not.
Dining chairs are the thin-section end of the catalogue, and thin sections are where moisture shows first. A 20 mm seat rail loses water faster than a 45 mm leg, and when it does, the rail shortens and the joint opens.
We dry to 8 to 12 percent and meter every batch. The reading is recorded against the batch number and printed on the packing list, so it can be checked at destination.
Home dining rooms, apartments and showrooms. Seat height 450 to 470 mm against a 720 to 750 mm table, seat depth 400 to 450 mm. Standard is domestic use under EN 12520, with EN 16139 Level 1 available where the chairs go into a serviced space.
The schedule
A kiln charge runs 15 to 25 days depending on species and section thickness, stepping temperature up and humidity down in stages. Rushing it by raising temperature early produces case-hardening: the outside of the board dries and locks while the core is still wet, and the board moves later, inside a finished chair.
Legs are cut from 42 to 50 mm square, seat rails from 20 to 25 mm, back posts 30 to 35 mm where the model carries a shaped back. The thin end — a 20 mm rail — is where drying matters most, because a thin section releases moisture fast and moves first.
Seat rails at 20 to 25 mm and legs at 42 to 50 mm do not dry at the same rate. Running them through one charge is the standard shortcut that produces a frame whose rails move after assembly, so we group by section rather than by order.
| Stage | Temperature | Duration | Purpose |
|---|---|---|---|
| Pre-heating | 40-50 °C, high humidity | 1-2 days | Warm the charge through |
| Main drying | 55-70 °C stepped | 10-18 days | Down to 12-14% |
| Equalising | 70-75 °C, low humidity | 2-4 days | Even out the core |
| Conditioning | Steam injection | 1-2 days | Relieve case-hardening |
| Cool and meter | Ambient | 1 day | Verify 8-12% before release |
Kiln schedule
Defects we reject for
End checking, collapse, honeycombing, sticker stain and fungal discolouration. Any of these disqualify a board from a frame component. They are cheap to reject at the kiln and expensive to discover after assembly. Solid Wood Dining Chairs use the same graded stock as every other model we build.
The seat is the surface people touch and see. A solid wood seat is sanded to a finer grit than the frame and the end grain is sealed, because a seat splits from the end outwards. Frames get the standard three-grit sequence.
Equilibrium, and what it means for your market
Timber settles at the moisture content the surrounding air dictates. A frame that arrives at 10 percent into a heated Nordic restaurant at 30 percent relative humidity will drop towards 6 percent and shrink as it does. That movement is normal and it is why we hold the band, seal end grain, and specify a joint that tolerates it.
A dining chair usually goes into a heated room and sits at 6 to 8 percent for months. Built at 12 percent, the rails shrink and the joints open; built at 8, it is stable. The band is chosen for the market, not for the kiln.
Species behave differently in the kiln
Ash — around 70% of what we run — dries steadily and holds its colour if the schedule is respected. Rubberwood, the other 30%, dries quickly and evenly and is the most forgiving charge in the yard. Oak is slow and prone to checking if pushed, and beech dries fast but collapses if the temperature goes up too early; both are custom runs for us. The schedule is written per species, not per thickness, and the two get confused constantly.
Around 70% of what we run is ash and roughly 30% rubberwood, and both appear in this category's charge book. Ash dries steadily and holds its colour; rubberwood dries fast and evenly. Both are metered the same way.
What dining chairs demand from the kiln
A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.
Seat rails are tenoned into the legs and the corner block is both glued and screwed. Screws alone work for a year; a glued block carries the racking load that a dining chair lives with. Turn the chair over and you can see the difference.
What happens after the kiln
Dried stock is held in a covered, conditioned store until it is machined. Leave it in an open yard through a Foshan wet season and it will take water back up within days, which undoes the schedule. This is the step most factories skip and the reason a moisture reading taken at packing matters more than one taken at the kiln.
We meter at both. If the two disagree, the charge goes back before it reaches the machining line.
Dining chair stock is the fastest moving inventory in the yard, which is good for turnover and bad for storage discipline: blanks left out through a Foshan wet season take water back within days. Covered store, metered at both ends.
Two per carton, 0.09 to 0.13 m³ a carton, most models knock-down so the seat and back come off the frame. MOQ is 6 pieces per model and mixed colours are allowed.
Which models this applies to
There are 269 models in this category: 82% run on a solid wood frame and 18% carry an upholstered or soft cover, so the moisture discipline applies to different components in different proportions.
Three of them as they stand today: A00101 (100% Wood, MOQ 6 pcs), A005 (Solid wood/Fabric, MOQ 6 pcs), A009 (100% Solid Wood, MOQ 6 pcs).
What moisture damage looks like on dining chairs
The returns are front leg joints loosening, seats splitting at the end grain where the finish did not cover it, and rocking from a frame machined out of tolerance. All three are visible in the first month, not the fifth year.
Domestic seating is tested under EN 12520 — seat and back fatigue, a leg forward load and a stability check. Light contract use moves to EN 16139 Level 1, which cycles the frame considerably harder.
Reading a moisture meter properly
Take three readings along a blank and average them, and correct for timber temperature. Pin meters, not pinless ones — and the reading that counts is the one taken at packing, not the one taken at the kiln.
Reference
Questions
What moisture content do you ship at?
8 to 12 percent, metered per batch, with the reading recorded on the packing list.
Does the schedule change for this category?
Seat rails at 20 to 25 mm and legs at 42 to 50 mm do not dry at the same rate. Running them through one charge is the standard shortcut that produces a frame whose rails move after assembly, so we group by section rather than by order.
Can I specify a tighter band?
Yes - say the target on the order and the charge is scheduled to it.
Does the schedule change for dining chairs?
A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.
What goes wrong on dining chairs if the moisture content is off?
The returns are front leg joints loosening, seats splitting at the end grain where the finish did not cover it, and rocking from a frame machined out of tolerance. All three are visible in the first month, not the fifth year.