Kiln schedule, the 8-12 percent band, case-hardening and why most joint failures in dining armchairs are actually moisture failures.
Why the kiln is the most important room in the factory
Most seating failures blamed on joinery are actually moisture failures. Timber that leaves a kiln too wet shrinks after it is made into a frame, and the glue line opens. The joint was fine; the water content was not.
Armchairs carry the thickest sections in the dining range and the most awkward shape. A shaped arm has to hold a curve and meet the back post at an angle, and both fail if the timber moves after it has been machined.
We dry to 8 to 12 percent and meter every batch. The reading is recorded against the batch number and printed on the packing list, so it can be checked at destination.
Head of table, banquets, clubs and hotel suites. Arm height matters as much as seat height: if the arm will not pass under the table apron, the chair cannot be pushed in and it blocks the room. Measure the apron before you order.
The schedule
A kiln charge runs 15 to 25 days depending on species and section thickness, stepping temperature up and humidity down in stages. Rushing it by raising temperature early produces case-hardening: the outside of the board dries and locks while the core is still wet, and the board moves later, inside a finished chair.
The arm is the heavy section: 35 to 45 mm where it meets the back post, tapering forward. Back posts run 35 to 40 mm because the arm loads them, and the seat rails 22 to 25 mm. Arms are cut from a blank thicker than anything a side chair uses.
Arm stock at 35 to 45 mm is the thickest material in this category and the slowest to dry. Push it and you get checking inside the arm, invisible under finish, and the arm later fails at the joint rather than in the middle.
| Stage | Temperature | Duration | Purpose |
|---|---|---|---|
| Pre-heating | 40-50 °C, high humidity | 1-2 days | Warm the charge through |
| Main drying | 55-70 °C stepped | 10-18 days | Down to 12-14% |
| Equalising | 70-75 °C, low humidity | 2-4 days | Even out the core |
| Conditioning | Steam injection | 1-2 days | Relieve case-hardening |
| Cool and meter | Ambient | 1 day | Verify 8-12% before release |
Kiln schedule
Defects we reject for
End checking, collapse, honeycombing, sticker stain and fungal discolouration. Any of these disqualify a board from a frame component. They are cheap to reject at the kiln and expensive to discover after assembly. Wooden Dining Armchairs use the same graded stock as every other model we build.
Arms are handled constantly and show wear first, so the top face and the front end take an extra pass and the finish is built slightly higher there. The underside of the arm is finished too — it is at eye level for anyone sitting beside it.
Equilibrium, and what it means for your market
Timber settles at the moisture content the surrounding air dictates. A frame that arrives at 10 percent into a heated Nordic restaurant at 30 percent relative humidity will drop towards 6 percent and shrink as it does. That movement is normal and it is why we hold the band, seal end grain, and specify a joint that tolerates it.
An arm is long, thick and shaped, and it moves further in absolute terms than any other component in this category. The joint at the back post is what has to tolerate that movement, which is why it is tenoned and bolted rather than glued on its own.
Species behave differently in the kiln
Ash — around 70% of what we run — dries steadily and holds its colour if the schedule is respected. Rubberwood, the other 30%, dries quickly and evenly and is the most forgiving charge in the yard. Oak is slow and prone to checking if pushed, and beech dries fast but collapses if the temperature goes up too early; both are custom runs for us. The schedule is written per species, not per thickness, and the two get confused constantly.
Arms are nearly always ash, because a shaped arm needs a timber that holds a curve and takes a knock; rubberwood marks too readily for a surface people grab. Most of the charge in this category is ash for that reason.
What dining armchairs demand from the kiln
An armchair is a dining chair with a lever attached. The arm is a cantilever: every time someone pushes themselves up, the load goes through the arm into the back post and out into the rear leg. That is the joint we reinforce, and it is why an armchair is heavier than the side chair it matches.
Arms are tenoned into the back post and through-bolted where the section allows. The arm to post joint failing is the single most common armchair return in the industry, and it is a specification problem, not a manufacturing one.
What happens after the kiln
Dried stock is held in a covered, conditioned store until it is machined. Leave it in an open yard through a Foshan wet season and it will take water back up within days, which undoes the schedule. This is the step most factories skip and the reason a moisture reading taken at packing matters more than one taken at the kiln.
We meter at both. If the two disagree, the charge goes back before it reaches the machining line.
Thick arm stock holds its moisture longer than the rails do, so the two are never stored together expecting the same behaviour. Arms are machined from stock held in the conditioned store at least a week after the kiln.
Packing runs 0.14 to 0.20 m³ for two with protective arm covers, because an arm is the easiest thing to damage in transit and the most expensive to replace. MOQ is 6 pieces per model.
Which models this applies to
There are 253 models in this category: 87% run on a solid wood frame and 13% carry an upholstered or soft cover, so the moisture discipline applies to different components in different proportions.
Three of them as they stand today: A0088 (100% Solid Wood, MOQ 6 pcs), XY-24018 (Solid wood, MOQ 6 pcs), A003 (100% Solid Wood, MOQ 6 pcs).
What moisture damage looks like on dining armchairs
Arm to post joints opening, arm pads worn through at the front where hands land, and frames that rock because the arm stiffened the back and the legs were not machined to suit. A heavier frame is not automatically a better one.
An armchair is tested for a downward and a sideways load on the arm itself, not only for seat and back fatigue. That arm load test is what separates a hospitality-grade armchair from a domestic one.
Reading a moisture meter properly
Take three readings along a blank and average them, and correct for timber temperature. Pin meters, not pinless ones — and the reading that counts is the one taken at packing, not the one taken at the kiln.
Reference
Questions
What moisture content do you ship at?
8 to 12 percent, metered per batch, with the reading recorded on the packing list.
Does the schedule change for this category?
Arm stock at 35 to 45 mm is the thickest material in this category and the slowest to dry. Push it and you get checking inside the arm, invisible under finish, and the arm later fails at the joint rather than in the middle.
Can I specify a tighter band?
Yes - say the target on the order and the charge is scheduled to it.
Does the schedule change for dining armchairs?
An armchair is a dining chair with a lever attached. The arm is a cantilever: every time someone pushes themselves up, the load goes through the arm into the back post and out into the rear leg. That is the joint we reinforce, and it is why an armchair is heavier than the side chair it matches.
What goes wrong on dining armchairs if the moisture content is off?
Arm to post joints opening, arm pads worn through at the front where hands land, and frames that rock because the arm stiffened the back and the legs were not machined to suit. A heavier frame is not automatically a better one.