Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Bar Stools

Sanding and Finishing Bar Stools: Three Grits to Final Coat

The sanding sequence, the raking-light inspection and the reference panel that decide how a bar stool looks under a dining room light.

Updated 2026-11-13Longjiang, Foshan11 min read

The sanding sequence, the raking-light inspection and the reference panel that decide how a bar stool looks under a dining room light.

These notes come off the production floor in Longjiang, Foshan. The current wooden bar stools supplier range is on the main site, with a specification page for every model in it.

Three grits, two inspections, one finish

Sanding is where a bar stool earns its surface. Three grits in sequence, an inspection under raking light between the second and third, and no finish until the bench signs off.

A stool is seen from below as often as from above — the underside of the seat and the footring sit at eye level for anyone at the bar. Both get the same three-grit sequence as the visible faces, and the ring is finished before it is welded.

Why sanding is compressed when a line is late

It is the easiest stage to rush and the first one the customer sees. A stain over a poorly sanded rail shows every scratch under a dining room light, so the schedule protects this bench, not the other way round.

The column and the footring are the thick sections here: a 45 to 60 mm column blank, a ring formed from 25 to 30 mm stock, seat blanks at 25 to 30 mm. On the swivel models the column is bought in as tube and machined to fit the mount.

StagePurposeCheck
Grit 1Flatten and shapeMachine marks gone
Grit 2Uniform scratchRaking-light inspection
Grit 3Finish preparationBench sign-off
Stain / sealerColour vs reference panelUnder D65 light
Top coatsScuff + tack betweenGloss and feel

Sanding sequence

Species sand differently

Open-grain timber drinks stain and shows swirl marks; tight grain shows gloss differences. Grit sequence and sanding direction are set per species, not per shift.

Most stools here run a wood seat on a wood or metal column, so the timber in the charge is seat stock — ash on roughly 70% of the programme, rubberwood on the rest. Plated metal components arrive finished and are not part of the moisture conversation at all.

Between coats, not just before them

Each finish coat gets a scuff and a tack cloth before the next; the final coat is compared against a sealed reference panel, not against the piece next to it.

Beyond the frame test a stool gets a stability check at height and a footring load test: push the ring sideways with the stool loaded and it must not deform. Swivel models are cycled, not just sat on.

The surface you will actually live with

Buyers ask about gloss and colour; the number that matters in service is how the finish stands up to cleaning agents, which is a packing-hall question as much as a spray-booth one.

Seat blanks for stools are small and they take water back quickly if they stand in an open yard. They move from the kiln to a covered store and are machined within the week, because a 25 mm blank has very little reserve.

The three returns we see: footring welds cracking after a season, swivel mechanisms that lose their gas, and seat pads compressed flat at the front edge. All three are specifiable — a closed-section ring, a contract-rated lift, and a 35 kg/m³ foam.

Questions

What sheen levels can I order?

Matt, satin and semi-gloss on wooden bar stools, all matched to a sealed panel rather than a photo.

Can you match a colour I send?

Physical samples, yes; screen colours, no. Colour is signed off on a stained panel before the batch runs.

How do you keep 300 bar stools the same colour?

One stain batch per order, one reference panel, and the booth checks against it - not against the previous chair.

What finishes are available?

NC, PU and water-based systems; the trade-offs are on the finishing page for wooden bar stools.