Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Solid Wood Dining Chairs

How a Dining Chair Sample Moves from Sketch to Golden Sample

The sample route for a dining chair - feasibility, first build, one revision round, and the sealed golden sample production is judged against.

Updated 2026-11-12Longjiang, Foshan11 min read

The sample route for a dining chair - feasibility, first build, one revision round, and the sealed golden sample production is judged against.

These notes come off the production floor in Longjiang, Foshan. The current solid wood dining chairs supplier range is on the main site, with a specification page for every model in it.

What a sample is for

A dining chair sample is not a scaled-down order; it is the agreement the whole order is checked against. Every dimension, finish and packing detail that appears on the golden sample becomes a checkpoint on the production line, which is why we treat sample work as a separate operation with its own bench and its own clock.

Dining chairs are the thin-section end of the catalogue, and thin sections are where moisture shows first. A 20 mm seat rail loses water faster than a 45 mm leg, and when it does, the rail shortens and the joint opens.

From enquiry to first sample

Buyer sends the model code or a drawing, the workshop pulls the timber and cuts one frame the same way production will - same jigs, same glue, same sanding sequence. A new dining chair sample takes 7 to 15 days depending on whether the tooling already exists.

Four legs, two side rails, two end rails and a back: the tenoner sets all of them in one fixture so a repeat order matches the first run. A tenon cut 1 mm small is a joint that stays loose for the life of the chair, and it cannot be seen until the frame is loaded.

StageWhat happensTime / output
1. EnquiryCode, drawing or photoFeasibility answer in 24 h
2. First sampleSame jigs as production7-15 days
3. RevisionOne consolidated round3-7 days
4. Golden sampleSigned and sealedTwo pieces: buyer + retained
5. ProductionChecked against retainedEvery carton

Sample route

The revision round

Revisions are cheapest before the sample leaves the factory. Height, seat depth, arm profile, foam firmness and stain colour can all be changed in one round; changing them after mass production starts means re-cutting the fixtures.

A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.

Seat rails are tenoned into the legs and the corner block is both glued and screwed. Screws alone work for a year; a glued block carries the racking load that a dining chair lives with. Turn the chair over and you can see the difference.

Golden sample and retained sample

Once approved, two samples are sealed: one travels to the buyer, one stays in the inspection area. Every carton of dining chairs shipped against that order is judged against the retained piece, not against memory.

Domestic seating is tested under EN 12520 — seat and back fatigue, a leg forward load and a stability check. Light contract use moves to EN 16139 Level 1, which cycles the frame considerably harder.

Samples from the current range

The catalogue lists 269 models in this category: 82% on a solid or wood frame and 18% with an upholstered or soft cover.

Ready-made references you can order straight away: A00105 (100% Wood, MOQ 6 pcs), A005 (Solid wood/Fabric, MOQ 6 pcs), A009 (100% Solid Wood, MOQ 6 pcs).

Questions

Do you charge for samples?

Sample cost and courier are quoted separately; the amount is credited against the mass production order once it is confirmed.

How many revisions can I make?

One consolidated round is normal. Each extra round adds roughly a week because the fixture changes have to be re-proven.

Is the sample made on the production line?

Yes - same jigs, same glue, same sanding. A sample made on a special bench tells you nothing about the 600 pieces that follow.

What is a golden sample?

The signed reference both sides agree to judge the order by. We keep one, you keep one.