Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Lounge Chairs

Machining Tolerances on Lounge Chairs: Where the Millimetre Is Decided

Tenons, holes and rails on a lounge chair are held to tenths of a millimetre - the checkpoints that keep a frame square for its whole service life.

Updated 2026-11-09Longjiang, Foshan11 min read

Tenons, holes and rails on a lounge chair are held to tenths of a millimetre - the checkpoints that keep a frame square for its whole service life.

These notes come off the production floor in Longjiang, Foshan. The current wooden lounge chairs range is on the main site, with a specification page for every model in it.

Tolerances are set at machining, nowhere else

A lounge chair frame either leaves the machine shop right or it never comes right. Glue can fill a visible gap but it cannot restore strength, so the millimetre is decided here - at the tenoner, the spindle moulder and the drill press.

Most of the frame here is machined for fit rather than for appearance: rails at 30 to 40 mm, a shaped ply or webbed seat deck, and no exposed joinery worth naming. Tolerance matters where the cover meets the frame, not where the eye looks.

Joint geometry before joint strength

The tenon is cut a hair proud and the mortise a hair tight, so assembly compresses the fibres and the joint locks itself. The fit is proven against a retained sample before the batch runs.

Frames are wood or metal under the cover, and the load path goes through the seat deck rather than the rails. Webbing or a sprung deck decides how the seat feels after a year more than the timber species does.

A lounge chair is a soft seat on a frame, not a frame with a pad. 220 of the 226 models in this category are upholstered, so the frame is a substrate: it has to hold the foam and the cover in shape under a sitter who stays put for an hour, not one who leaves in twenty minutes.

FeatureToleranceHow it is checked
Tenon width±0.2 mmGauge every 10th blank
Mortise depth±0.3 mmDepth stop verified at set-up
Hole spacing±0.5 mmDrill jig + plug gauge
Seat rail length±0.5 mmStop block, verified per batch
Surface flatnessRaking lightBefore finishing

Machining checkpoints

Checking without stopping the line

One in ten lounge chairs blanks goes over the bench during the run: gauge the tenon width, seat depth and hole spacing. If two in a row drift, the cutter gets re-sharpened before anything else moves.

The frame is a substrate for upholstery, so sections run lighter than a dining chair: 30 to 40 mm on the load-bearing rails, with a shaped ply or a webbed deck carrying the seat. Timber here is dried for stability rather than for appearance — most of it is never seen.

Wood is still moving after machining

Kiln-dried timber is not finished moving. Boards are allowed to equalise in the workshop before cutting, and machined parts are joined within days, not weeks, so the frame and the environment agree on a moisture number.

Upholstered frames are dried for stability rather than for looks: a rail that moves inside a cover shows as a wrinkle or a split seam instead of a crack, and it is far harder to diagnose afterwards. This stock is held to the tighter end of the band.

An upholstered frame is buffered: the cover and the foam slow the exchange with room air, so the frame moves more slowly than an exposed dining chair and it moves somewhere else. The risk is a seam that opens in month six, not a joint that opens in week one.

Where tolerance mistakes show up later

Not on day one. They show up as a creaking lounge chair in year two, which is why the retained sample and the gauge routine exist.

Seats that bottom out, covers that pill at the front edge, and frames that creak because the deck was stapled rather than webbed. Comfort complaints are almost always foam density, not frame strength.

Questions

What tolerance do you hold?

Joint-critical features are held to ±0.2-0.5 mm depending on the feature; the numbers are on the specification sheet for each lounge chair model.

Why does glue not fix a loose joint?

Glue has strength but no stiffness at the surface - a filled joint flexes, works loose and fails long before the wood does.

Do you check every piece?

One in ten during the run plus a first-article check at set-up; the gauge card travels with the batch.

Can I specify tighter tolerances?

Yes, and it is priced in machine time. Tell us which dimension matters for the installation and we will hold it.