Tenons, holes and rails on a dining chair are held to tenths of a millimetre - the checkpoints that keep a frame square for its whole service life.
Tolerances are set at machining, nowhere else
A dining chair frame either leaves the machine shop right or it never comes right. Glue can fill a visible gap but it cannot restore strength, so the millimetre is decided here - at the tenoner, the spindle moulder and the drill press.
Four legs, two side rails, two end rails and a back: the tenoner sets all of them in one fixture so a repeat order matches the first run. A tenon cut 1 mm small is a joint that stays loose for the life of the chair, and it cannot be seen until the frame is loaded.
Joint geometry before joint strength
The tenon is cut a hair proud and the mortise a hair tight, so assembly compresses the fibres and the joint locks itself. The fit is proven against a retained sample before the batch runs.
Seat rails are tenoned into the legs and the corner block is both glued and screwed. Screws alone work for a year; a glued block carries the racking load that a dining chair lives with. Turn the chair over and you can see the difference.
A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.
| Feature | Tolerance | How it is checked |
|---|---|---|
| Tenon width | ±0.2 mm | Gauge every 10th blank |
| Mortise depth | ±0.3 mm | Depth stop verified at set-up |
| Hole spacing | ±0.5 mm | Drill jig + plug gauge |
| Seat rail length | ±0.5 mm | Stop block, verified per batch |
| Surface flatness | Raking light | Before finishing |
Machining checkpoints
Checking without stopping the line
One in ten dining chairs blanks goes over the bench during the run: gauge the tenon width, seat depth and hole spacing. If two in a row drift, the cutter gets re-sharpened before anything else moves.
Legs are cut from 42 to 50 mm square, seat rails from 20 to 25 mm, back posts 30 to 35 mm where the model carries a shaped back. The thin end — a 20 mm rail — is where drying matters most, because a thin section releases moisture fast and moves first.
Wood is still moving after machining
Kiln-dried timber is not finished moving. Boards are allowed to equalise in the workshop before cutting, and machined parts are joined within days, not weeks, so the frame and the environment agree on a moisture number.
Seat rails at 20 to 25 mm and legs at 42 to 50 mm do not dry at the same rate. Running them through one charge is the standard shortcut that produces a frame whose rails move after assembly, so we group by section rather than by order.
A dining chair usually goes into a heated room and sits at 6 to 8 percent for months. Built at 12 percent, the rails shrink and the joints open; built at 8, it is stable. The band is chosen for the market, not for the kiln.
Where tolerance mistakes show up later
Not on day one. They show up as a creaking dining chair in year two, which is why the retained sample and the gauge routine exist.
The returns are front leg joints loosening, seats splitting at the end grain where the finish did not cover it, and rocking from a frame machined out of tolerance. All three are visible in the first month, not the fifth year.
Reference
Questions
What tolerance do you hold?
Joint-critical features are held to ±0.2-0.5 mm depending on the feature; the numbers are on the specification sheet for each dining chair model.
Why does glue not fix a loose joint?
Glue has strength but no stiffness at the surface - a filled joint flexes, works loose and fails long before the wood does.
Do you check every piece?
One in ten during the run plus a first-article check at set-up; the gauge card travels with the batch.
Can I specify tighter tolerances?
Yes, and it is priced in machine time. Tell us which dimension matters for the installation and we will hold it.