Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Bar Stools

Machining Tolerances on Bar Stools: Where the Millimetre Is Decided

Tenons, holes and rails on a bar stool are held to tenths of a millimetre - the checkpoints that keep a frame square for its whole service life.

Updated 2026-11-08Longjiang, Foshan11 min read

Tenons, holes and rails on a bar stool are held to tenths of a millimetre - the checkpoints that keep a frame square for its whole service life.

These notes come off the production floor in Longjiang, Foshan. The current wooden bar stools supplier range is on the main site, with a specification page for every model in it.

Tolerances are set at machining, nowhere else

A bar stool frame either leaves the machine shop right or it never comes right. Glue can fill a visible gap but it cannot restore strength, so the millimetre is decided here - at the tenoner, the spindle moulder and the drill press.

The column is turned or machined from a single blank wherever the model allows, because a jointed column on a high stool is a wobble waiting to happen. On swivel models the mount plate is machined to fit the tube rather than welded to a rough cut.

Joint geometry before joint strength

The tenon is cut a hair proud and the mortise a hair tight, so assembly compresses the fibres and the joint locks itself. The fit is proven against a retained sample before the batch runs.

The critical junction is where the column meets the seat mount and where the footring meets the column. On a swivel model the gas lift is a bought-in component and we test the assembly, not just the frame: a lift rated for office duty is not the same part as one rated for a bar that runs twelve hours a day.

A stool carries its load differently from a chair. The seat is high, the base is narrow relative to the height, and the footring takes a sideways kick every time someone climbs on or pushes off. That is why the ring on our stools is a welded closed section joined to the column, not a ring screwed into a leg.

FeatureToleranceHow it is checked
Tenon width±0.2 mmGauge every 10th blank
Mortise depth±0.3 mmDepth stop verified at set-up
Hole spacing±0.5 mmDrill jig + plug gauge
Seat rail length±0.5 mmStop block, verified per batch
Surface flatnessRaking lightBefore finishing

Machining checkpoints

Checking without stopping the line

One in ten bar stools blanks goes over the bench during the run: gauge the tenon width, seat depth and hole spacing. If two in a row drift, the cutter gets re-sharpened before anything else moves.

The column and the footring are the thick sections here: a 45 to 60 mm column blank, a ring formed from 25 to 30 mm stock, seat blanks at 25 to 30 mm. On the swivel models the column is bought in as tube and machined to fit the mount.

Wood is still moving after machining

Kiln-dried timber is not finished moving. Boards are allowed to equalise in the workshop before cutting, and machined parts are joined within days, not weeks, so the frame and the environment agree on a moisture number.

A stool column is a thick section and a footring is a bent one, and both come out of the same charge as thinner seat blanks. That is exactly the case where one schedule delivers two moisture contents, so the thick stock is dried separately.

Stool columns are thick and they respond slowly to a change in humidity, which helps: a column that arrives at 10 percent will not fall to 6 percent in a week. The seat, at 25 mm, will. That mismatch inside one product is why components are metered separately.

Where tolerance mistakes show up later

Not on day one. They show up as a creaking bar stool in year two, which is why the retained sample and the gauge routine exist.

The three returns we see: footring welds cracking after a season, swivel mechanisms that lose their gas, and seat pads compressed flat at the front edge. All three are specifiable — a closed-section ring, a contract-rated lift, and a 35 kg/m³ foam.

Questions

What tolerance do you hold?

Joint-critical features are held to ±0.2-0.5 mm depending on the feature; the numbers are on the specification sheet for each bar stool model.

Why does glue not fix a loose joint?

Glue has strength but no stiffness at the surface - a filled joint flexes, works loose and fails long before the wood does.

Do you check every piece?

One in ten during the run plus a first-article check at set-up; the gauge card travels with the batch.

Can I specify tighter tolerances?

Yes, and it is priced in machine time. Tell us which dimension matters for the installation and we will hold it.