Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Lounge Chairs

Fixtures and Jigs: How Lounge Chairs Stay Consistent at Volume

Per-model jig sets, first-article checks and scheduled fixture maintenance - why lounge chairs number 300 matches number 1.

Updated 2026-11-05Longjiang, Foshan11 min read

Per-model jig sets, first-article checks and scheduled fixture maintenance - why lounge chairs number 300 matches number 1.

These notes come off the production floor in Longjiang, Foshan. The current wholesale wooden lounge chairs range is on the main site, with a specification page for every model in it.

Consistency is a fixture problem

The difference between lounge chairs number 1 and number 300 is not the worker's mood; it is the fixture. Drill jigs, glue racks and assembly stops turn a skill into a process.

Most of the frame here is machined for fit rather than for appearance: rails at 30 to 40 mm, a shaped ply or webbed seat deck, and no exposed joinery worth naming. Tolerance matters where the cover meets the frame, not where the eye looks.

One fixture set per model

Each lounge chair model has its own jig set, stored and tagged with the model code. When an order re-runs a year later, the same stops and bushes come off the shelf, which is why a repeat order matches the first one.

The frame is a substrate for upholstery, so sections run lighter than a dining chair: 30 to 40 mm on the load-bearing rails, with a shaped ply or a webbed deck carrying the seat. Timber here is dried for stability rather than for appearance — most of it is never seen.

DisciplineHowWhat it buys
Per-model jig setTagged with model codeRepeat orders match
First articleMeasured vs retained sampleGate before the run
In-run gauge1 in 10 blanksDrift caught early
Fixture inspectionScheduledWear re-cut, not tolerated
StorageRacked by codeNothing improvised

Fixture discipline

First-article check at set-up

Every fixture set-up starts with a first article measured against the retained sample. The line does not run until the first piece passes; that single rule removes most of the batch-level surprises.

The frame is assembled, then the deck is webbed or sprung, then the foam goes on and the cover is fitted. The frame joint is only half the job; the other half is how the soft parts are held in shape, which is a different skill on the line.

Comfort testing counts as much as strength here: foam compression set under repeated loading, cover abrasion, and a frame fatigue test at Level 1 or Level 2 depending on the traffic the lobby actually sees.

Fixtures wear, so they are checked

Bushes elongate, stops wear, glue racks accumulate. Fixture condition is inspected on a schedule, and a worn jig is re-cut - because drift on the fixture becomes drift on every piece after it.

Seats that bottom out, covers that pill at the front edge, and frames that creak because the deck was stapled rather than webbed. Comfort complaints are almost always foam density, not frame strength.

What this means for the buyer

Re-orders match. The lounge chair you reordered this year sits with the ones you bought last year, which is the whole point of writing the process down.

The bulky end of the catalogue: 0.22 to 0.34 m³ per carton, one piece, fully assembled. Freight dominates the landed cost, which is why buyers consolidate them with flatter models. MOQ is 4 pieces, and 2 on some models.

Questions

How do you keep a repeat order identical?

Same fixture set, same retained sample, same gauge routine - the process, not the people, carries the consistency.

Can you match lounge chairs we bought elsewhere?

Send us one piece or the drawings; we build a fixture set and prove it on a first article before mass production.

What happens when a jig wears?

It is re-cut on schedule. Drift is caught by the in-run gauge long before a buyer sees it.

Do fixtures slow down small orders?

No - the same fixtures run a 6-piece order and a 600-piece order, which is why small wooden lounge chairs orders ship on the same quality curve.