Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Bar Stools

Hardware on Bar Stools: What We Specify and Why

Inserts, levelers and coated call-outs - the hardware specification that keeps a bar stool serviceable for years.

Updated 2026-11-02Longjiang, Foshan11 min read

Inserts, levelers and coated call-outs - the hardware specification that keeps a bar stool serviceable for years.

These notes come off the production floor in Longjiang, Foshan. The current wooden bar stools range is on the main site, with a specification page for every model in it.

Hardware is specified, not grabbed

Every screw, insert and bracket on a bar stool has a written call-out - thread, length, coating. The bin shelf is organised by specification because a half-millimetre of screw length is the difference between a tight joint and a stripped insert.

Assembly runs vertically: seat mount first, then the footring, then the seat. Clamping a stool square is harder than clamping a chair because the column gives you nothing to reference against — the jig does the work.

Inserts where the buyer needs service

Seat decks, arm pads and leveler feet land on threaded inserts, not bare wood. The insert housing is drilled to gauge and glued, so the thread survives repeated assembly.

The critical junction is where the column meets the seat mount and where the footring meets the column. On a swivel model the gas lift is a bought-in component and we test the assembly, not just the frame: a lift rated for office duty is not the same part as one rated for a bar that runs twelve hours a day.

A stool carries its load differently from a chair. The seat is high, the base is narrow relative to the height, and the footring takes a sideways kick every time someone climbs on or pushes off. That is why the ring on our stools is a welded closed section joined to the column, not a ring screwed into a leg.

ItemSpecificationWhere it matters
InsertsThreaded, glued housingServiceable joints
ScrewsLength by specNo stripped threads
LevelersNylon or steelFloor type at the venue
BracketsCoated per climateDestination humidity
Spare kitIn every cartonPacking list verified

Hardware call-outs

Levelers and the floor question

Restaurant floors are rarely flat. Leveler feet on bar stools are specified for the venue type - nylon for tile, steel for something rougher - and adjusted before the frame leaves the bench.

Height decides everything: 650 mm seat for a 900 mm bar top, 750 mm for a 1050 mm counter. Get it wrong by 50 mm and the sitter either perches or cannot reach the top. Kitchen islands in apartments are the fastest growing part of this category.

Coating decides where it can ship

Plated and coated hardware is chosen against the destination climate; coastal and humid projects get a different call-out than inland ones. It is a packing-list line item, not an afterthought.

Stools pack small — 0.08 to 0.12 m³ for two — so the freight per piece is the best in the catalogue and a 40HC holds a lot of them. MOQ is 6 pieces per model.

Hardware in the inspection

Torque checks on inserts, fit checks on levelers, and a hardware count against the carton list at packing - the two screws missing in carton one are the claim nobody wants.

Beyond the frame test a stool gets a stability check at height and a footring load test: push the ring sideways with the stool loaded and it must not deform. Swivel models are cycled, not just sat on.

Questions

Is hardware included in the carton?

Yes, plus a small spare kit; the packing list counts hardware the same way it counts frames.

Can I get a specific hardware brand?

Yes for project orders - the call-out is written into the specification for wooden bar stools.

Do levelers come fitted?

Fitted and pre-adjusted; the buyer only trims them on site.

What hardware fails in service?

Almost none of it - failures come from missing spares or wrong-length screws after a re-assembly, both of which the spare kit covers.