Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Bar Stools

Joints Used in Our Bar Stools: Mortise, Dowel and Bolt

Which joints carry which load on a bar stool, and why glue, dowels and bolts are kept in separate jobs.

Updated 2026-11-01Longjiang, Foshan11 min read

Which joints carry which load on a bar stool, and why glue, dowels and bolts are kept in separate jobs.

These notes come off the production floor in Longjiang, Foshan. The current wooden bar stools range is on the main site, with a specification page for every model in it.

Three joint families on one bar stool

Mortise and tenon carries the load, dowels locate the parts, and bolts hold what the buyer will assemble or adjust later. Each does one job; problems start when a joint is asked to do all three.

The critical junction is where the column meets the seat mount and where the footring meets the column. On a swivel model the gas lift is a bought-in component and we test the assembly, not just the frame: a lift rated for office duty is not the same part as one rated for a bar that runs twelve hours a day.

Where mortise and tenon goes

Leg-to-rail and any joint that takes a bending load. The shoulder hides the glue line and the long grain gives the glue somewhere to work.

A stool carries its load differently from a chair. The seat is high, the base is narrow relative to the height, and the footring takes a sideways kick every time someone climbs on or pushes off. That is why the ring on our stools is a welded closed section joined to the column, not a ring screwed into a leg.

JointUsed forWhy
Mortise & tenonLoad-bearing framesBending and racking loads
DowelFlat part alignmentLocation, light loads
Bolt + insertServiceable partsDisassembly and adjustment
Corner blockInside every rail junctionRacking resistance
Glue lineAll of the aboveContinuity, not gap filling

Joint selection

Where dowels and bolts go

Dowels align and locate flat parts; bolts and inserts carry parts the user will service - seat decks, arm pads, leveler feet. A bolted joint in a bar stool is a feature, not a shortcut, as long as the insert is properly housed.

Assembly runs vertically: seat mount first, then the footring, then the seat. Clamping a stool square is harder than clamping a chair because the column gives you nothing to reference against — the jig does the work.

What a good joint looks like finished

No visible glue, no gap you can slide paper into, and no wobble with the frame off the bench. The finish is only as honest as the joint under it.

A stool is seen from below as often as from above — the underside of the seat and the footring sit at eye level for anyone at the bar. Both get the same three-grit sequence as the visible faces, and the ring is finished before it is welded.

How joints fail

In service it is almost always moisture or overloading, not the joint itself - which is why the timber numbers matter as much as the fit.

The three returns we see: footring welds cracking after a season, swivel mechanisms that lose their gas, and seat pads compressed flat at the front edge. All three are specifiable — a closed-section ring, a contract-rated lift, and a 35 kg/m³ foam.

Beyond the frame test a stool gets a stability check at height and a footring load test: push the ring sideways with the stool loaded and it must not deform. Swivel models are cycled, not just sat on.

Questions

Are your joints glued or screwed?

Both, where each belongs: glued joinery carries the frame, bolts only where the buyer benefits from assembly or adjustment.

Can I get knock-down bar stools?

Yes. KD versions use bolted inserts at the serviceable points and the frame is engineered so racking strength does not depend on the bolts.

What joint lasts longest?

A properly fitted mortise and tenon in dry timber. The kiln record matters as much as the fit.

How are joints tested?

Static load and racking tests per batch, judged against the retained sample.