Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Restaurant Chairs

Foam, Covers and Upholstery Work on Restaurant Chairs

Foam density, the seat deck under it, and the nested cutting that turns cloth into covers on restaurant chairs.

Updated 2026-10-31Longjiang, Foshan12 min read

Foam density, the seat deck under it, and the nested cutting that turns cloth into covers on restaurant chairs.

These notes come off the production floor in Longjiang, Foshan. The current restaurant chairs range is on the main site, with a specification page for every model in it.

Foam is chosen by density, never by feel alone

Seat foam on a restaurant chair is specified by density and firmness, written into the model specification. Two foams can feel identical in the showroom and behave completely differently after a year of service.

Covers are chosen for cleanability: PU, leather and tight-weave fabric, abrasion 30,000 rubs and up. A restaurant that cannot wipe a seat down in ten seconds will not keep it in service for a year.

The seat deck underneath decides the feel

Foam sits on a deck - elastic webbing, springs or a formed plywood panel. The deck sets the base firmness; the foam tunes it. Changing foam without looking at the deck is how soft seats end up bottoming out.

A restaurant chair is specified for turnover, not for comfort in the abstract. It gets sat in hard, dragged across a floor and wiped down several times a day. Frames are built to EN 16139 Level 2 and the seat is designed to survive cleaning, which rules out a lot of domestic construction.

LayerWhat it isWhat it decides
DeckWebbing / springs / plyBase firmness
FoamDensity-specifiedComfort tuning
CoverNested cutting, sewnWaste + alignment
FittingFixed sequenceOne in ten bench check
Front edgeReinforcedFirst place wear shows

Seat build

Covers are cut from nested markers

Upholstery covers are nested on the cloth to control waste, cut, sewn and fitted over the foam on a fixed sequence. Seam alignment and foam density are checked on the bench, one in ten.

Covers are chosen for cleanability: PU, leather and tight-weave fabric, abrasion 30,000 rubs and up. A restaurant that cannot wipe a seat down in ten seconds will not keep it in service for a year.

EN 16139 Level 2 is the contract grade: higher cycle counts on seat and back, a leg forward load, and a stability test that assumes the user does not sit down gently. Reports are raised per model, not per range.

Comfort is a scene question

A café restaurant chair lives 12 hours a day and needs a firmer seat; a home dining restaurant chair is judged in the first hour. Same foam chemistry, different specification.

Restaurants, cafés, bistros and hotel dining rooms — the largest category we build, 490 models. Stacking four to six high is common because rooms get re-set, and a stackable frame is a different engineering job from a knock-down one.

What wears out first

Almost always the front edge of the seat - cover abrasion and foam collapse together. It is the reason we hold the density line even when a cheaper foam passes the showroom test.

Seats delaminating under daily wiping, stretchers loosening on models that get dragged rather than lifted, and finishes going dull where the cleaning agent is too alkaline. Ask what cleaner the operator uses.

Upholstered models in this range

The catalogue lists 486 models in this category: 85% on a solid or wood frame and 15% with an upholstered or soft cover.

Upholstered references: A008 (100% Solid Wood, MOQ 2 pcs), XY-24018 (Solid wood, MOQ 6 pcs), A00311 (100% Solid Wood, MOQ 6 pcs).

Questions

What foam density do you use?

Seat foam is specified per model in the restaurant chairs range; contract projects usually take the higher-density option and home ranges the mid one.

Can I send my own fabric?

Yes - COM orders are welcome; we test stitchability and shrinkage before cutting.

Why is my sample seat firmer than the photo suggested?

Showroom light flatters soft foam. Density numbers, not photos, are what the order is built on.

How long should the seat last?

With the specified density and a contract-grade cover, years of daily service; the front edge is the honest wear indicator.