Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Lounge Chairs

Foam, Covers and Upholstery Work on Lounge Chairs

Foam density, the seat deck under it, and the nested cutting that turns cloth into covers on lounge chairs.

Updated 2026-10-31Longjiang, Foshan12 min read

Foam density, the seat deck under it, and the nested cutting that turns cloth into covers on lounge chairs.

These notes come off the production floor in Longjiang, Foshan. The current wooden lounge chairs range is on the main site, with a specification page for every model in it.

Foam is chosen by density, never by feel alone

Seat foam on a lounge chair is specified by density and firmness, written into the model specification. Two foams can feel identical in the showroom and behave completely differently after a year of service.

Foam density is the specification that matters: 30 to 35 kg/m³ for a lobby, lower for a showroom piece. Covers are velvet, fabric or leather, and where the market requires it we can supply to BS 5852 or CAL 117 — specify at quotation, not after.

The seat deck underneath decides the feel

Foam sits on a deck - elastic webbing, springs or a formed plywood panel. The deck sets the base firmness; the foam tunes it. Changing foam without looking at the deck is how soft seats end up bottoming out.

A lounge chair is a soft seat on a frame, not a frame with a pad. 220 of the 226 models in this category are upholstered, so the frame is a substrate: it has to hold the foam and the cover in shape under a sitter who stays put for an hour, not one who leaves in twenty minutes.

LayerWhat it isWhat it decides
DeckWebbing / springs / plyBase firmness
FoamDensity-specifiedComfort tuning
CoverNested cutting, sewnWaste + alignment
FittingFixed sequenceOne in ten bench check
Front edgeReinforcedFirst place wear shows

Seat build

Covers are cut from nested markers

Upholstery covers are nested on the cloth to control waste, cut, sewn and fitted over the foam on a fixed sequence. Seam alignment and foam density are checked on the bench, one in ten.

Foam density is the specification that matters: 30 to 35 kg/m³ for a lobby, lower for a showroom piece. Covers are velvet, fabric or leather, and where the market requires it we can supply to BS 5852 or CAL 117 — specify at quotation, not after.

Comfort testing counts as much as strength here: foam compression set under repeated loading, cover abrasion, and a frame fatigue test at Level 1 or Level 2 depending on the traffic the lobby actually sees.

Comfort is a scene question

A café lounge chair lives 12 hours a day and needs a firmer seat; a home dining lounge chair is judged in the first hour. Same foam chemistry, different specification.

Hotel lobbies, waiting areas, senior living, reading corners. Seat height 400 to 430 mm with the back raked further than a dining chair, because the sitter is resting rather than eating. A side table at 350 to 400 mm goes with it.

What wears out first

Almost always the front edge of the seat - cover abrasion and foam collapse together. It is the reason we hold the density line even when a cheaper foam passes the showroom test.

Seats that bottom out, covers that pill at the front edge, and frames that creak because the deck was stapled rather than webbed. Comfort complaints are almost always foam density, not frame strength.

Upholstered models in this range

The catalogue lists 225 models in this category: 1% on a solid or wood frame and 99% with an upholstered or soft cover.

Upholstered references: GDC-5652 (Velvet/Fabric/Leather, MOQ 2 pcs), GDC-5652 (Velvet/Fabric/Leather, MOQ 2 pcs), GDC-5652 (Velvet/Fabric/Leather, MOQ 4 pcs).

Questions

What foam density do you use?

Seat foam is specified per model in the wooden lounge chairs range; contract projects usually take the higher-density option and home ranges the mid one.

Can I send my own fabric?

Yes - COM orders are welcome; we test stitchability and shrinkage before cutting.

Why is my sample seat firmer than the photo suggested?

Showroom light flatters soft foam. Density numbers, not photos, are what the order is built on.

How long should the seat last?

With the specified density and a contract-grade cover, years of daily service; the front edge is the honest wear indicator.