Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Dining Armchairs

Foam, Covers and Upholstery Work on Dining Armchairs

Foam density, the seat deck under it, and the nested cutting that turns cloth into covers on dining armchairs.

Updated 2026-10-31Longjiang, Foshan12 min read

Foam density, the seat deck under it, and the nested cutting that turns cloth into covers on dining armchairs.

These notes come off the production floor in Longjiang, Foshan. The current wooden dining armchairs supplier range is on the main site, with a specification page for every model in it.

Foam is chosen by density, never by feel alone

Seat foam on a dining armchair is specified by density and firmness, written into the model specification. Two foams can feel identical in the showroom and behave completely differently after a year of service.

Arms are the hardest part to cover cleanly. On upholstered models the cover is cut with the pattern running along the arm rather than around it, because an arm seen from above shows every mistake in the lay of the fabric.

The seat deck underneath decides the feel

Foam sits on a deck - elastic webbing, springs or a formed plywood panel. The deck sets the base firmness; the foam tunes it. Changing foam without looking at the deck is how soft seats end up bottoming out.

An armchair is a dining chair with a lever attached. The arm is a cantilever: every time someone pushes themselves up, the load goes through the arm into the back post and out into the rear leg. That is the joint we reinforce, and it is why an armchair is heavier than the side chair it matches.

LayerWhat it isWhat it decides
DeckWebbing / springs / plyBase firmness
FoamDensity-specifiedComfort tuning
CoverNested cutting, sewnWaste + alignment
FittingFixed sequenceOne in ten bench check
Front edgeReinforcedFirst place wear shows

Seat build

Covers are cut from nested markers

Upholstery covers are nested on the cloth to control waste, cut, sewn and fitted over the foam on a fixed sequence. Seam alignment and foam density are checked on the bench, one in ten.

Arms are the hardest part to cover cleanly. On upholstered models the cover is cut with the pattern running along the arm rather than around it, because an arm seen from above shows every mistake in the lay of the fabric.

An armchair is tested for a downward and a sideways load on the arm itself, not only for seat and back fatigue. That arm load test is what separates a hospitality-grade armchair from a domestic one.

Comfort is a scene question

A café dining armchair lives 12 hours a day and needs a firmer seat; a home dining dining armchair is judged in the first hour. Same foam chemistry, different specification.

Head of table, banquets, clubs and hotel suites. Arm height matters as much as seat height: if the arm will not pass under the table apron, the chair cannot be pushed in and it blocks the room. Measure the apron before you order.

What wears out first

Almost always the front edge of the seat - cover abrasion and foam collapse together. It is the reason we hold the density line even when a cheaper foam passes the showroom test.

Arm to post joints opening, arm pads worn through at the front where hands land, and frames that rock because the arm stiffened the back and the legs were not machined to suit. A heavier frame is not automatically a better one.

Upholstered models in this range

The catalogue lists 253 models in this category: 87% on a solid or wood frame and 13% with an upholstered or soft cover.

Upholstered references: A0092 (100% Solid Wood, MOQ 6 pcs), XY-24068 (Solid wood, MOQ 6 pcs), A005 (Solid wood/rattan, MOQ 6 pcs).

Questions

What foam density do you use?

Seat foam is specified per model in the wooden dining armchairs range; contract projects usually take the higher-density option and home ranges the mid one.

Can I send my own fabric?

Yes - COM orders are welcome; we test stitchability and shrinkage before cutting.

Why is my sample seat firmer than the photo suggested?

Showroom light flatters soft foam. Density numbers, not photos, are what the order is built on.

How long should the seat last?

With the specified density and a contract-grade cover, years of daily service; the front edge is the honest wear indicator.