Foam density, the seat deck under it, and the nested cutting that turns cloth into covers on bar stools.
Foam is chosen by density, never by feel alone
Seat foam on a bar stool is specified by density and firmness, written into the model specification. Two foams can feel identical in the showroom and behave completely differently after a year of service.
Seats are the part that fails first on a stool. Leather and velvet covers around 26 of the 88 models take a knee-slide load that a dining chair never sees, so the seam is placed away from the front edge and the foam is wrapped rather than loose.
The seat deck underneath decides the feel
Foam sits on a deck - elastic webbing, springs or a formed plywood panel. The deck sets the base firmness; the foam tunes it. Changing foam without looking at the deck is how soft seats end up bottoming out.
A stool carries its load differently from a chair. The seat is high, the base is narrow relative to the height, and the footring takes a sideways kick every time someone climbs on or pushes off. That is why the ring on our stools is a welded closed section joined to the column, not a ring screwed into a leg.
| Layer | What it is | What it decides |
|---|---|---|
| Deck | Webbing / springs / ply | Base firmness |
| Foam | Density-specified | Comfort tuning |
| Cover | Nested cutting, sewn | Waste + alignment |
| Fitting | Fixed sequence | One in ten bench check |
| Front edge | Reinforced | First place wear shows |
Seat build
Covers are cut from nested markers
Upholstery covers are nested on the cloth to control waste, cut, sewn and fitted over the foam on a fixed sequence. Seam alignment and foam density are checked on the bench, one in ten.
Seats are the part that fails first on a stool. Leather and velvet covers around 26 of the 88 models take a knee-slide load that a dining chair never sees, so the seam is placed away from the front edge and the foam is wrapped rather than loose.
Beyond the frame test a stool gets a stability check at height and a footring load test: push the ring sideways with the stool loaded and it must not deform. Swivel models are cycled, not just sat on.
Comfort is a scene question
A café bar stool lives 12 hours a day and needs a firmer seat; a home dining bar stool is judged in the first hour. Same foam chemistry, different specification.
Height decides everything: 650 mm seat for a 900 mm bar top, 750 mm for a 1050 mm counter. Get it wrong by 50 mm and the sitter either perches or cannot reach the top. Kitchen islands in apartments are the fastest growing part of this category.
What wears out first
Almost always the front edge of the seat - cover abrasion and foam collapse together. It is the reason we hold the density line even when a cheaper foam passes the showroom test.
The three returns we see: footring welds cracking after a season, swivel mechanisms that lose their gas, and seat pads compressed flat at the front edge. All three are specifiable — a closed-section ring, a contract-rated lift, and a 35 kg/m³ foam.
Upholstered models in this range
The catalogue lists 86 models in this category: 44% on a solid or wood frame and 33% with an upholstered or soft cover.
Upholstered references: A001 (100% Solid Wood, MOQ 2 pcs), A10035 (Solid Wood, MOQ 4 pcs), by-62565 (Leather/Velvet/Fabric, MOQ 4 pcs).
Reference
Questions
What foam density do you use?
Seat foam is specified per model in the wooden bar stools range; contract projects usually take the higher-density option and home ranges the mid one.
Can I send my own fabric?
Yes - COM orders are welcome; we test stitchability and shrinkage before cutting.
Why is my sample seat firmer than the photo suggested?
Showroom light flatters soft foam. Density numbers, not photos, are what the order is built on.
How long should the seat last?
With the specified density and a contract-grade cover, years of daily service; the front edge is the honest wear indicator.