The seven operations a restaurant chair passes through in our Longjiang factory - equipment, cycle time and the inspection checkpoint at each stage.
One site, seven operations
Every restaurant chair we ship passes through the same building in Longjiang. Nothing is outsourced except the plating of metal components, which is why a question about a joint can be answered in an hour rather than a week.
The line runs: cutting, machining, sanding, assembly, finishing, upholstery, packing. The table below is the actual sequence with the checkpoint at each stage, not a marketing diagram.
Restaurants, cafés, bistros and hotel dining rooms — the largest category we build, 490 models. Stacking four to six high is common because rooms get re-set, and a stackable frame is a different engineering job from a knock-down one.
How restaurant chairs differ on the line
A restaurant chair is specified for turnover, not for comfort in the abstract. It gets sat in hard, dragged across a floor and wiped down several times a day. Frames are built to EN 16139 Level 2 and the seat is designed to survive cleaning, which rules out a lot of domestic construction.
Corner blocks glued and screwed, stretchers on the heavier models, and a seat rail section big enough to take a repeated racking load. The test regime cycles the frame far harder than a domestic standard does.
| Stage | Equipment | Checkpoint |
|---|---|---|
| 1. Cutting | Cross-cut and rip saws | Blank dimensions, grain direction |
| 2. Machining | Tenoner, spindle moulder, CNC | Joint fit against retained sample |
| 3. Sanding | Three-grit sequence | Surface inspection under raking light |
| 4. Assembly | Glue, clamp, corner blocks | Clamp time, squareness, joint gap |
| 5. Finishing | Filtered spray booth | Colour vs sealed reference panel |
| 6. Upholstery | Cutting, sewing, fitting | Seam alignment, foam density check |
| 7. Packing | 5-ply carton, EPE, corner board | Drop test on first carton |
Production sequence
Cutting and machining
Timber arrives kiln-dried and is cut to blank, then machined on the tenoner and the spindle moulder. This is where the joint geometry is set, and it is the only stage where a mistake is unrecoverable — a tenon cut 1 mm small is a loose joint for the life of the chair.
Contract frames are machined heavier: legs at 45 to 55 mm, rails at 25 to 30 mm, and a stretcher mortised in on the models that get dragged rather than lifted. That stretcher joint decides whether the chair survives a year of being pulled across a floor.
Contract sections run heavier than domestic: 45 to 55 mm legs, 25 to 30 mm rails, and a stretcher on the models that get dragged rather than lifted. The extra section is not for show — it is what survives a room being re-set several times a day.
Sanding, and why it takes three passes
Three grits, progressively finer, with a inspection between the second and the third. Sanding is the operation most likely to be compressed when a line is behind schedule, and it is the one the customer notices first — a finish applied over a poorly sanded frame shows every scratch under a dining room light.
Finishes are specified for cleaning, not for depth of sheen. A restaurant seat is wiped with an alkaline agent several times a day, so the coating is chosen for chemical resistance, and the seat edges where the cloth catches are the first thing inspected.
Assembly
Stackable models are assembled to a tighter squareness tolerance than a domestic chair, because a stack of six that does not sit true puts a permanent twist into the frames at the bottom. The jig is checked per run, not per season.
Frames for our restaurant chairs go through the same fixture set whether the order is 6 pieces or 600.
Upholstery and packing
Covers are cut from nested markers to control waste, sewn, then fitted over foam on a seat deck built the same way every time. Final packing is five-ply carton, EPE between components, corner board on frame ends, and a drop test on the first carton of a new model.
Then the container: cartons are stacked to a loading plan, photographed at three points, and sealed. Those photographs are what settle a damage claim.
Covers are chosen for cleanability: PU, leather and tight-weave fabric, abrasion 30,000 rubs and up. A restaurant that cannot wipe a seat down in ten seconds will not keep it in service for a year.
Two per carton, 0.10 to 0.15 m³, stackable or knock-down. MOQ is 6 pieces per model, and most buyers run two to four models in one container.
What restaurant chairs look like in our catalogue
There are 486 models in this category: 85% run on a solid wood frame and 15% carry an upholstered or soft cover. The mix decides what the line has to be good at.
Three of them as they stand today: A005 (Solid wood/rattan, MOQ 6 pcs), XY-24018 (Solid wood, MOQ 6 pcs), A00137 (100% Wood, MOQ 6 pcs).
Where restaurant chairs fail in service
Seats delaminating under daily wiping, stretchers loosening on models that get dragged rather than lifted, and finishes going dull where the cleaning agent is too alkaline. Ask what cleaner the operator uses.
EN 16139 Level 2 is the contract grade: higher cycle counts on seat and back, a leg forward load, and a stability test that assumes the user does not sit down gently. Reports are raised per model, not per range.
Reference
Questions
Where is the factory?
Longjiang, Shunde, Foshan, Guangdong. All seven operations run in one building; only metal plating is outsourced.
Can I visit?
Yes. Buyers are welcome on the line. A factory that runs its own line will show all of it.
How long does a run take?
25 to 40 days from deposit depending on finish and season, plus 7 to 15 days for a sample if the model is new to us.
What is different about building restaurant chairs?
A restaurant chair is specified for turnover, not for comfort in the abstract. It gets sat in hard, dragged across a floor and wiped down several times a day. Frames are built to EN 16139 Level 2 and the seat is designed to survive cleaning, which rules out a lot of domestic construction.
What fails first on restaurant chairs?
Seats delaminating under daily wiping, stretchers loosening on models that get dragged rather than lifted, and finishes going dull where the cleaning agent is too alkaline. Ask what cleaner the operator uses.