Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Solid Wood Dining Chairs

How Dining Chairs Are Built: Inside a Foshan Chair Line

The seven operations a dining chair passes through in our Longjiang factory - equipment, cycle time and the inspection checkpoint at each stage.

Updated 2026-11-14Longjiang, Foshan14 min read

The seven operations a dining chair passes through in our Longjiang factory - equipment, cycle time and the inspection checkpoint at each stage.

These notes come off the production floor in Longjiang, Foshan. The current solid wood dining chairs range is on the main site, with a specification page for every model in it.

One site, seven operations

Every dining chair we ship passes through the same building in Longjiang. Nothing is outsourced except the plating of metal components, which is why a question about a joint can be answered in an hour rather than a week.

The line runs: cutting, machining, sanding, assembly, finishing, upholstery, packing. The table below is the actual sequence with the checkpoint at each stage, not a marketing diagram.

Home dining rooms, apartments and showrooms. Seat height 450 to 470 mm against a 720 to 750 mm table, seat depth 400 to 450 mm. Standard is domestic use under EN 12520, with EN 16139 Level 1 available where the chairs go into a serviced space.

How dining chairs differ on the line

A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.

Seat rails are tenoned into the legs and the corner block is both glued and screwed. Screws alone work for a year; a glued block carries the racking load that a dining chair lives with. Turn the chair over and you can see the difference.

StageEquipmentCheckpoint
1. CuttingCross-cut and rip sawsBlank dimensions, grain direction
2. MachiningTenoner, spindle moulder, CNCJoint fit against retained sample
3. SandingThree-grit sequenceSurface inspection under raking light
4. AssemblyGlue, clamp, corner blocksClamp time, squareness, joint gap
5. FinishingFiltered spray boothColour vs sealed reference panel
6. UpholsteryCutting, sewing, fittingSeam alignment, foam density check
7. Packing5-ply carton, EPE, corner boardDrop test on first carton

Production sequence

Cutting and machining

Timber arrives kiln-dried and is cut to blank, then machined on the tenoner and the spindle moulder. This is where the joint geometry is set, and it is the only stage where a mistake is unrecoverable — a tenon cut 1 mm small is a loose joint for the life of the chair.

Four legs, two side rails, two end rails and a back: the tenoner sets all of them in one fixture so a repeat order matches the first run. A tenon cut 1 mm small is a joint that stays loose for the life of the chair, and it cannot be seen until the frame is loaded.

Legs are cut from 42 to 50 mm square, seat rails from 20 to 25 mm, back posts 30 to 35 mm where the model carries a shaped back. The thin end — a 20 mm rail — is where drying matters most, because a thin section releases moisture fast and moves first.

Sanding, and why it takes three passes

Three grits, progressively finer, with a inspection between the second and the third. Sanding is the operation most likely to be compressed when a line is behind schedule, and it is the one the customer notices first — a finish applied over a poorly sanded frame shows every scratch under a dining room light.

The seat is the surface people touch and see. A solid wood seat is sanded to a finer grit than the frame and the end grain is sealed, because a seat splits from the end outwards. Frames get the standard three-grit sequence.

Assembly

Frames go together on a jig that holds the seat square while the glue cures. Clamp time is fixed to the adhesive specification, and the corner blocks are both glued and screwed rather than one or the other.

Frames for our solid wood dining chairs go through the same fixture set whether the order is 6 pieces or 600.

Upholstery and packing

Covers are cut from nested markers to control waste, sewn, then fitted over foam on a seat deck built the same way every time. Final packing is five-ply carton, EPE between components, corner board on frame ends, and a drop test on the first carton of a new model.

Then the container: cartons are stacked to a loading plan, photographed at three points, and sealed. Those photographs are what settle a damage claim.

Roughly two thirds of this category is a solid wood frame with a wood seat; the rest carries a padded seat or a woven seat. Covers on the padded models are cut to a nested marker so a repeat order matches the original run.

Two per carton, 0.09 to 0.13 m³ a carton, most models knock-down so the seat and back come off the frame. MOQ is 6 pieces per model and mixed colours are allowed.

What dining chairs look like in our catalogue

There are 269 models in this category: 82% run on a solid wood frame and 18% carry an upholstered or soft cover. The mix decides what the line has to be good at.

Three of them as they stand today: A00105 (100% Wood, MOQ 6 pcs), A005 (Solid wood/Leather, MOQ 6 pcs), A009 (100% Solid Wood, MOQ 6 pcs).

Where dining chairs fail in service

The returns are front leg joints loosening, seats splitting at the end grain where the finish did not cover it, and rocking from a frame machined out of tolerance. All three are visible in the first month, not the fifth year.

Domestic seating is tested under EN 12520 — seat and back fatigue, a leg forward load and a stability check. Light contract use moves to EN 16139 Level 1, which cycles the frame considerably harder.

Questions

Where is the factory?

Longjiang, Shunde, Foshan, Guangdong. All seven operations run in one building; only metal plating is outsourced.

Can I visit?

Yes. Buyers are welcome on the line. A factory that runs its own line will show all of it.

How long does a run take?

25 to 40 days from deposit depending on finish and season, plus 7 to 15 days for a sample if the model is new to us.

What is different about building dining chairs?

A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.

What fails first on dining chairs?

The returns are front leg joints loosening, seats splitting at the end grain where the finish did not cover it, and rocking from a frame machined out of tolerance. All three are visible in the first month, not the fifth year.