Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Dining Armchairs

How Dining Armchairs Are Built: Inside a Foshan Chair Line

The seven operations a dining armchair passes through in our Longjiang factory - equipment, cycle time and the inspection checkpoint at each stage.

Updated 2026-11-14Longjiang, Foshan14 min read

The seven operations a dining armchair passes through in our Longjiang factory - equipment, cycle time and the inspection checkpoint at each stage.

These notes come off the production floor in Longjiang, Foshan. The current wholesale wooden dining armchairs range is on the main site, with a specification page for every model in it.

One site, seven operations

Every dining armchair we ship passes through the same building in Longjiang. Nothing is outsourced except the plating of metal components, which is why a question about a joint can be answered in an hour rather than a week.

The line runs: cutting, machining, sanding, assembly, finishing, upholstery, packing. The table below is the actual sequence with the checkpoint at each stage, not a marketing diagram.

Head of table, banquets, clubs and hotel suites. Arm height matters as much as seat height: if the arm will not pass under the table apron, the chair cannot be pushed in and it blocks the room. Measure the apron before you order.

How dining armchairs differ on the line

An armchair is a dining chair with a lever attached. The arm is a cantilever: every time someone pushes themselves up, the load goes through the arm into the back post and out into the rear leg. That is the joint we reinforce, and it is why an armchair is heavier than the side chair it matches.

Arms are tenoned into the back post and through-bolted where the section allows. The arm to post joint failing is the single most common armchair return in the industry, and it is a specification problem, not a manufacturing one.

StageEquipmentCheckpoint
1. CuttingCross-cut and rip sawsBlank dimensions, grain direction
2. MachiningTenoner, spindle moulder, CNCJoint fit against retained sample
3. SandingThree-grit sequenceSurface inspection under raking light
4. AssemblyGlue, clamp, corner blocksClamp time, squareness, joint gap
5. FinishingFiltered spray boothColour vs sealed reference panel
6. UpholsteryCutting, sewing, fittingSeam alignment, foam density check
7. Packing5-ply carton, EPE, corner boardDrop test on first carton

Production sequence

Cutting and machining

Timber arrives kiln-dried and is cut to blank, then machined on the tenoner and the spindle moulder. This is where the joint geometry is set, and it is the only stage where a mistake is unrecoverable — a tenon cut 1 mm small is a loose joint for the life of the chair.

The arm is the expensive machining job in this category. It is a shaped, tapered component that has to meet the back post at a fixed angle, and that tenon is cut on the tenoner rather than by hand — a hand-cut arm joint is the failure we get called about.

The arm is the heavy section: 35 to 45 mm where it meets the back post, tapering forward. Back posts run 35 to 40 mm because the arm loads them, and the seat rails 22 to 25 mm. Arms are cut from a blank thicker than anything a side chair uses.

Sanding, and why it takes three passes

Three grits, progressively finer, with a inspection between the second and the third. Sanding is the operation most likely to be compressed when a line is behind schedule, and it is the one the customer notices first — a finish applied over a poorly sanded frame shows every scratch under a dining room light.

Arms are handled constantly and show wear first, so the top face and the front end take an extra pass and the finish is built slightly higher there. The underside of the arm is finished too — it is at eye level for anyone sitting beside it.

Assembly

The sequence changes for an armchair: the back assembly is built first, then the arms are fitted to it, then the frame is closed. Assembling an armchair the way you assemble a side chair leaves the arm joint last, where it cannot be clamped.

Frames for our wooden dining armchairs go through the same fixture set whether the order is 6 pieces or 600.

Upholstery and packing

Covers are cut from nested markers to control waste, sewn, then fitted over foam on a seat deck built the same way every time. Final packing is five-ply carton, EPE between components, corner board on frame ends, and a drop test on the first carton of a new model.

Then the container: cartons are stacked to a loading plan, photographed at three points, and sealed. Those photographs are what settle a damage claim.

Arms are the hardest part to cover cleanly. On upholstered models the cover is cut with the pattern running along the arm rather than around it, because an arm seen from above shows every mistake in the lay of the fabric.

Packing runs 0.14 to 0.20 m³ for two with protective arm covers, because an arm is the easiest thing to damage in transit and the most expensive to replace. MOQ is 6 pieces per model.

What dining armchairs look like in our catalogue

There are 253 models in this category: 87% run on a solid wood frame and 13% carry an upholstered or soft cover. The mix decides what the line has to be good at.

Three of them as they stand today: A00105 (100% Wood, MOQ 6 pcs), A005 (Ash wood, MOQ 6 pcs), XY-24018 (Solid wood, MOQ 6 pcs).

Where dining armchairs fail in service

Arm to post joints opening, arm pads worn through at the front where hands land, and frames that rock because the arm stiffened the back and the legs were not machined to suit. A heavier frame is not automatically a better one.

An armchair is tested for a downward and a sideways load on the arm itself, not only for seat and back fatigue. That arm load test is what separates a hospitality-grade armchair from a domestic one.

Questions

Where is the factory?

Longjiang, Shunde, Foshan, Guangdong. All seven operations run in one building; only metal plating is outsourced.

Can I visit?

Yes. Buyers are welcome on the line. A factory that runs its own line will show all of it.

How long does a run take?

25 to 40 days from deposit depending on finish and season, plus 7 to 15 days for a sample if the model is new to us.

What is different about building dining armchairs?

An armchair is a dining chair with a lever attached. The arm is a cantilever: every time someone pushes themselves up, the load goes through the arm into the back post and out into the rear leg. That is the joint we reinforce, and it is why an armchair is heavier than the side chair it matches.

What fails first on dining armchairs?

Arm to post joints opening, arm pads worn through at the front where hands land, and frames that rock because the arm stiffened the back and the legs were not machined to suit. A heavier frame is not automatically a better one.