The seven operations a bar stool passes through in our Longjiang factory - equipment, cycle time and the inspection checkpoint at each stage.
One site, seven operations
Every bar stool we ship passes through the same building in Longjiang. Nothing is outsourced except the plating of metal components, which is why a question about a joint can be answered in an hour rather than a week.
The line runs: cutting, machining, sanding, assembly, finishing, upholstery, packing. The table below is the actual sequence with the checkpoint at each stage, not a marketing diagram.
Height decides everything: 650 mm seat for a 900 mm bar top, 750 mm for a 1050 mm counter. Get it wrong by 50 mm and the sitter either perches or cannot reach the top. Kitchen islands in apartments are the fastest growing part of this category.
How bar stools differ on the line
A stool carries its load differently from a chair. The seat is high, the base is narrow relative to the height, and the footring takes a sideways kick every time someone climbs on or pushes off. That is why the ring on our stools is a welded closed section joined to the column, not a ring screwed into a leg.
The critical junction is where the column meets the seat mount and where the footring meets the column. On a swivel model the gas lift is a bought-in component and we test the assembly, not just the frame: a lift rated for office duty is not the same part as one rated for a bar that runs twelve hours a day.
| Stage | Equipment | Checkpoint |
|---|---|---|
| 1. Cutting | Cross-cut and rip saws | Blank dimensions, grain direction |
| 2. Machining | Tenoner, spindle moulder, CNC | Joint fit against retained sample |
| 3. Sanding | Three-grit sequence | Surface inspection under raking light |
| 4. Assembly | Glue, clamp, corner blocks | Clamp time, squareness, joint gap |
| 5. Finishing | Filtered spray booth | Colour vs sealed reference panel |
| 6. Upholstery | Cutting, sewing, fitting | Seam alignment, foam density check |
| 7. Packing | 5-ply carton, EPE, corner board | Drop test on first carton |
Production sequence
Cutting and machining
Timber arrives kiln-dried and is cut to blank, then machined on the tenoner and the spindle moulder. This is where the joint geometry is set, and it is the only stage where a mistake is unrecoverable — a tenon cut 1 mm small is a loose joint for the life of the chair.
The column is turned or machined from a single blank wherever the model allows, because a jointed column on a high stool is a wobble waiting to happen. On swivel models the mount plate is machined to fit the tube rather than welded to a rough cut.
The column and the footring are the thick sections here: a 45 to 60 mm column blank, a ring formed from 25 to 30 mm stock, seat blanks at 25 to 30 mm. On the swivel models the column is bought in as tube and machined to fit the mount.
Sanding, and why it takes three passes
Three grits, progressively finer, with a inspection between the second and the third. Sanding is the operation most likely to be compressed when a line is behind schedule, and it is the one the customer notices first — a finish applied over a poorly sanded frame shows every scratch under a dining room light.
A stool is seen from below as often as from above — the underside of the seat and the footring sit at eye level for anyone at the bar. Both get the same three-grit sequence as the visible faces, and the ring is finished before it is welded.
Assembly
Assembly runs vertically: seat mount first, then the footring, then the seat. Clamping a stool square is harder than clamping a chair because the column gives you nothing to reference against — the jig does the work.
Frames for our wooden bar stools go through the same fixture set whether the order is 6 pieces or 600.
Upholstery and packing
Covers are cut from nested markers to control waste, sewn, then fitted over foam on a seat deck built the same way every time. Final packing is five-ply carton, EPE between components, corner board on frame ends, and a drop test on the first carton of a new model.
Then the container: cartons are stacked to a loading plan, photographed at three points, and sealed. Those photographs are what settle a damage claim.
Seats are the part that fails first on a stool. Leather and velvet covers around 26 of the 88 models take a knee-slide load that a dining chair never sees, so the seam is placed away from the front edge and the foam is wrapped rather than loose.
Stools pack small — 0.08 to 0.12 m³ for two — so the freight per piece is the best in the catalogue and a 40HC holds a lot of them. MOQ is 6 pieces per model.
What bar stools look like in our catalogue
There are 86 models in this category: 44% run on a solid wood frame and 33% carry an upholstered or soft cover. The mix decides what the line has to be good at.
Three of them as they stand today: by-62565 (Leather/Velvet/Fabric, MOQ 6 pcs), A001 (100% Metal, MOQ 50 pcs), A10037 (Solid Wood, MOQ 6 pcs).
Where bar stools fail in service
The three returns we see: footring welds cracking after a season, swivel mechanisms that lose their gas, and seat pads compressed flat at the front edge. All three are specifiable — a closed-section ring, a contract-rated lift, and a 35 kg/m³ foam.
Beyond the frame test a stool gets a stability check at height and a footring load test: push the ring sideways with the stool loaded and it must not deform. Swivel models are cycled, not just sat on.
Reference
Questions
Where is the factory?
Longjiang, Shunde, Foshan, Guangdong. All seven operations run in one building; only metal plating is outsourced.
Can I visit?
Yes. Buyers are welcome on the line. A factory that runs its own line will show all of it.
How long does a run take?
25 to 40 days from deposit depending on finish and season, plus 7 to 15 days for a sample if the model is new to us.
What is different about building bar stools?
A stool carries its load differently from a chair. The seat is high, the base is narrow relative to the height, and the footring takes a sideways kick every time someone climbs on or pushes off. That is why the ring on our stools is a welded closed section joined to the column, not a ring screwed into a leg.
What fails first on bar stools?
The three returns we see: footring welds cracking after a season, swivel mechanisms that lose their gas, and seat pads compressed flat at the front edge. All three are specifiable — a closed-section ring, a contract-rated lift, and a 35 kg/m³ foam.