Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Lounge Chairs

Choosing Lounge Chairs for Cafés and Tea Shops

Twelve-hour days, nightly scrubbing and hourly re-arranging - which lounge chair specifications survive real café service.

Updated 2026-10-21Longjiang, Foshan11 min read

Twelve-hour days, nightly scrubbing and hourly re-arranging - which lounge chair specifications survive real café service.

These notes come off the production floor in Longjiang, Foshan. The current wooden lounge chairs supplier range is on the main site, with a specification page for every model in it.

A café is a turnover problem

Café seating works 12 hours a day, gets scrubbed nightly and is re-arranged hourly. The right lounge chair here is not the prettiest one - it is the one whose wear points survive that routine.

Hotel lobbies, waiting areas, senior living, reading corners. Seat height 400 to 430 mm with the back raked further than a dining chair, because the sitter is resting rather than eating. A side table at 350 to 400 mm goes with it.

What actually breaks in cafés

Front seat edges, levelers and finish under cleaning agents - in that order. Specifications that survive cafés are written around those three, not around showroom looks.

Seats that bottom out, covers that pill at the front edge, and frames that creak because the deck was stapled rather than webbed. Comfort complaints are almost always foam density, not frame strength.

Frames for upholstery go straight from the conditioned store to machining, because a frame that has picked up moisture will move after the cover is fitted — and a cover hides that movement until the seam splits.

ItemWhat to checkWhy
Wear pointsFront edge, levelers, finishSpecified above catalogue average
CleaningAgents agreed up frontAftercare sheet ships with order
LayoutStacking if floor re-sets dailyEngineered, not improvised
Comfort window12 h daysFirmer foam than home
Reorder pathFixture sets keptRepeat orders match

Café seating checklist

Stacking and re-arranging

If the venue re-sets the floor daily, stackability and frame protection matter more than anything on the mood board. Stacking lounge chairs are engineered differently and priced differently.

A lounge chair is a soft seat on a frame, not a frame with a pad. 220 of the 226 models in this category are upholstered, so the frame is a substrate: it has to hold the foam and the cover in shape under a sitter who stays put for an hour, not one who leaves in twenty minutes.

The cleaning contract

Covers and finishes should be chosen with the cleaning list in hand; the aftercare sheet ships with the order so the nightly routine matches the material.

Foam density is the specification that matters: 30 to 35 kg/m³ for a lobby, lower for a showroom piece. Covers are velvet, fabric or leather, and where the market requires it we can supply to BS 5852 or CAL 117 — specify at quotation, not after.

Frames for upholstery go straight from the conditioned store to machining, because a frame that has picked up moisture will move after the cover is fitted — and a cover hides that movement until the seam splits.

Ordering for a café fit-out

The most common order quantity in this category is 4 pcs (144 models ship at that level).

Mid-range references cafés reorder most: GDC-5652 (Velvet/Fabric/Leather, MOQ 2 pcs), GDC-5652 (Velvet/Fabric/Leather, MOQ 4 pcs), GDC-5652 (Velvet/Fabric/Leather, MOQ 4 pcs).

Questions

How many lounge chairs do I need for a 40-seat café?

Seating counts follow the floor plan; what we can promise is that the models you pick reorder identically a year later.

Do café lounge chairs need special finishes?

A cleaning-resistant finish system, yes - it is a specification choice, not an upgrade.

What MOQ applies to a fit-out?

The most common order quantity in this category is 4 pcs (144 models ship at that level).

Can I visit the line before ordering?

Yes - buyers are welcome in Longjiang, and a café buyer should see the wear-point inspections in person.