Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Solid Wood Dining Chairs

Choosing Dining Chairs for Cafés and Tea Shops

Twelve-hour days, nightly scrubbing and hourly re-arranging - which dining chair specifications survive real café service.

Updated 2026-10-21Longjiang, Foshan11 min read

Twelve-hour days, nightly scrubbing and hourly re-arranging - which dining chair specifications survive real café service.

These notes come off the production floor in Longjiang, Foshan. The current wholesale solid wood dining chairs range is on the main site, with a specification page for every model in it.

A café is a turnover problem

Café seating works 12 hours a day, gets scrubbed nightly and is re-arranged hourly. The right dining chair here is not the prettiest one - it is the one whose wear points survive that routine.

Home dining rooms, apartments and showrooms. Seat height 450 to 470 mm against a 720 to 750 mm table, seat depth 400 to 450 mm. Standard is domestic use under EN 12520, with EN 16139 Level 1 available where the chairs go into a serviced space.

What actually breaks in cafés

Front seat edges, levelers and finish under cleaning agents - in that order. Specifications that survive cafés are written around those three, not around showroom looks.

The returns are front leg joints loosening, seats splitting at the end grain where the finish did not cover it, and rocking from a frame machined out of tolerance. All three are visible in the first month, not the fifth year.

Dining chair stock is the fastest moving inventory in the yard, which is good for turnover and bad for storage discipline: blanks left out through a Foshan wet season take water back within days. Covered store, metered at both ends.

ItemWhat to checkWhy
Wear pointsFront edge, levelers, finishSpecified above catalogue average
CleaningAgents agreed up frontAftercare sheet ships with order
LayoutStacking if floor re-sets dailyEngineered, not improvised
Comfort window12 h daysFirmer foam than home
Reorder pathFixture sets keptRepeat orders match

Café seating checklist

Stacking and re-arranging

If the venue re-sets the floor daily, stackability and frame protection matter more than anything on the mood board. Stacking dining chairs are engineered differently and priced differently.

A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.

The cleaning contract

Covers and finishes should be chosen with the cleaning list in hand; the aftercare sheet ships with the order so the nightly routine matches the material.

Roughly two thirds of this category is a solid wood frame with a wood seat; the rest carries a padded seat or a woven seat. Covers on the padded models are cut to a nested marker so a repeat order matches the original run.

Dining chair stock is the fastest moving inventory in the yard, which is good for turnover and bad for storage discipline: blanks left out through a Foshan wet season take water back within days. Covered store, metered at both ends.

Ordering for a café fit-out

The most common order quantity in this category is 6 pcs (221 models ship at that level).

Mid-range references cafés reorder most: A00105 (100% Wood, MOQ 6 pcs), A005 (Solid wood/Leather, MOQ 6 pcs), A009 (100% Solid Wood, MOQ 6 pcs).

Questions

How many dining chairs do I need for a 40-seat café?

Seating counts follow the floor plan; what we can promise is that the models you pick reorder identically a year later.

Do café dining chairs need special finishes?

A cleaning-resistant finish system, yes - it is a specification choice, not an upgrade.

What MOQ applies to a fit-out?

The most common order quantity in this category is 6 pcs (221 models ship at that level).

Can I visit the line before ordering?

Yes - buyers are welcome in Longjiang, and a café buyer should see the wear-point inspections in person.