Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Dining Armchairs

Choosing Dining Armchairs for Cafés and Tea Shops

Twelve-hour days, nightly scrubbing and hourly re-arranging - which dining armchair specifications survive real café service.

Updated 2026-10-21Longjiang, Foshan11 min read

Twelve-hour days, nightly scrubbing and hourly re-arranging - which dining armchair specifications survive real café service.

These notes come off the production floor in Longjiang, Foshan. The current wholesale wooden dining armchairs range is on the main site, with a specification page for every model in it.

A café is a turnover problem

Café seating works 12 hours a day, gets scrubbed nightly and is re-arranged hourly. The right dining armchair here is not the prettiest one - it is the one whose wear points survive that routine.

Head of table, banquets, clubs and hotel suites. Arm height matters as much as seat height: if the arm will not pass under the table apron, the chair cannot be pushed in and it blocks the room. Measure the apron before you order.

What actually breaks in cafés

Front seat edges, levelers and finish under cleaning agents - in that order. Specifications that survive cafés are written around those three, not around showroom looks.

Arm to post joints opening, arm pads worn through at the front where hands land, and frames that rock because the arm stiffened the back and the legs were not machined to suit. A heavier frame is not automatically a better one.

Thick arm stock holds its moisture longer than the rails do, so the two are never stored together expecting the same behaviour. Arms are machined from stock held in the conditioned store at least a week after the kiln.

ItemWhat to checkWhy
Wear pointsFront edge, levelers, finishSpecified above catalogue average
CleaningAgents agreed up frontAftercare sheet ships with order
LayoutStacking if floor re-sets dailyEngineered, not improvised
Comfort window12 h daysFirmer foam than home
Reorder pathFixture sets keptRepeat orders match

Café seating checklist

Stacking and re-arranging

If the venue re-sets the floor daily, stackability and frame protection matter more than anything on the mood board. Stacking dining armchairs are engineered differently and priced differently.

An armchair is a dining chair with a lever attached. The arm is a cantilever: every time someone pushes themselves up, the load goes through the arm into the back post and out into the rear leg. That is the joint we reinforce, and it is why an armchair is heavier than the side chair it matches.

The cleaning contract

Covers and finishes should be chosen with the cleaning list in hand; the aftercare sheet ships with the order so the nightly routine matches the material.

Arms are the hardest part to cover cleanly. On upholstered models the cover is cut with the pattern running along the arm rather than around it, because an arm seen from above shows every mistake in the lay of the fabric.

Thick arm stock holds its moisture longer than the rails do, so the two are never stored together expecting the same behaviour. Arms are machined from stock held in the conditioned store at least a week after the kiln.

Ordering for a café fit-out

The most common order quantity in this category is 6 pcs (207 models ship at that level).

Mid-range references cafés reorder most: XY-24018 (Solid wood, MOQ 6 pcs), A00137 (100% Wood, MOQ 6 pcs), A005 (Solid wood/Fabric, MOQ 6 pcs).

Questions

How many dining armchairs do I need for a 40-seat café?

Seating counts follow the floor plan; what we can promise is that the models you pick reorder identically a year later.

Do café dining armchairs need special finishes?

A cleaning-resistant finish system, yes - it is a specification choice, not an upgrade.

What MOQ applies to a fit-out?

The most common order quantity in this category is 6 pcs (207 models ship at that level).

Can I visit the line before ordering?

Yes - buyers are welcome in Longjiang, and a café buyer should see the wear-point inspections in person.