Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Solid Wood Dining Chairs

Dining Chairs for Banquet Halls: Stacking, Uniformity, Waves

Five hundred seats stored Monday, seated Saturday - the engineering and logistics behind banquet-grade dining chairs.

Updated 2026-10-20Longjiang, Foshan11 min read

Five hundred seats stored Monday, seated Saturday - the engineering and logistics behind banquet-grade dining chairs.

These notes come off the production floor in Longjiang, Foshan. The current solid wood dining chairs supplier range is on the main site, with a specification page for every model in it.

Banquet seating is logistics wearing furniture

A banquet hall stores 500 dining chairs on Monday and seats 500 guests on Saturday. Uniformity, stackability and repair-ability outrank every aesthetic question.

Home dining rooms, apartments and showrooms. Seat height 450 to 470 mm against a 720 to 750 mm table, seat depth 400 to 450 mm. Standard is domestic use under EN 12520, with EN 16139 Level 1 available where the chairs go into a serviced space.

Stacking is engineering

Stack loads, leg alignment and protective spacing are designed in, not discovered on site. A dining chair that stacks ten high needs frames that stay square after a hundred stacks.

A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.

ItemDesign pointService reality
StackingDesigned loads + spacingSquare after 100 stacks
UniformityOne fixture setNo wobble at table nine
StorageCartons for racks/trolleysPads counted as parts
WavesRetained samples keptSeason re-orders match
RepairServiceable jointsVenue team can fix

Banquet checklist

Uniformity across hundreds

Guests notice wobble at table nine. One fixture set runs the whole order and the in-run gauge keeps dining chair number 480 as square as number 8.

Four legs, two side rails, two end rails and a back: the tenoner sets all of them in one fixture so a repeat order matches the first run. A tenon cut 1 mm small is a joint that stays loose for the life of the chair, and it cannot be seen until the frame is loaded.

Domestic seating is tested under EN 12520 — seat and back fatigue, a leg forward load and a stability check. Light contract use moves to EN 16139 Level 1, which cycles the frame considerably harder.

Storage and transport

Cartons are sized for trolley lanes and storage racks, and the packing list counts protective pads as seriously as frames - storage damage is banquet damage.

Two per carton, 0.09 to 0.13 m³ a carton, most models knock-down so the seat and back come off the frame. MOQ is 6 pieces per model and mixed colours are allowed.

Through the season

Banquet houses re-order in waves before event seasons; retained samples and kept fixtures mean wave two matches wave one.

Dining chair stock is the fastest moving inventory in the yard, which is good for turnover and bad for storage discipline: blanks left out through a Foshan wet season take water back within days. Covered store, metered at both ends.

References banquet buyers reorder: A005 (Solid wood/Fabric, MOQ 6 pcs), XY-24018 (Solid wood, MOQ 6 pcs), A001348 (100% Wood, MOQ 6 pcs).

Questions

What MOQ applies to banquet orders?

The most common order quantity in this category is 6 pcs (221 models ship at that level).

Do banquet dining chairs need special frames?

Stack-rated frames with reinforced junctions - a standard frame stacked nightly will not survive a season.

Can waves ship months apart?

Yes, fixtures and retained samples are retained so later waves match.

What about venue repairs?

Serviceable joints and a spare kit per carton; the venue team handles most repairs without the factory.