Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Solid Wood Dining Chairs

Glue, Clamp Time and Corner Blocks on Dining Chairs

Moisture, spread, open time and clamp pressure - the four controls that turn glue from a bottle into a process on dining chairs.

Updated 2026-10-17Longjiang, Foshan11 min read

Moisture, spread, open time and clamp pressure - the four controls that turn glue from a bottle into a process on dining chairs.

These notes come off the production floor in Longjiang, Foshan. The current wholesale solid wood dining chairs range is on the main site, with a specification page for every model in it.

Glue is a process, not a bottle

The adhesive matters less than the four things around it: moisture of the timber, spread rate, open time and clamp pressure. On a dining chair line those four are written down and checked, because they are the difference between a glue line and a glue film.

Frames go together on a jig that holds the seat square while the glue cures. Clamp time is fixed to the adhesive specification, and the corner blocks are both glued and screwed rather than one or the other.

Clamp time is not negotiable

Parts come off the clamp bench on a timer, not on feel. A dining chair frame unclamped early holds its shape for a day and walks for a year - the rail drifts out of square and the seat deck never sits flat again.

Seat rails at 20 to 25 mm and legs at 42 to 50 mm do not dry at the same rate. Running them through one charge is the standard shortcut that produces a frame whose rails move after assembly, so we group by section rather than by order.

Control pointTargetVerification
Timber moisture8-12%Meter per batch, on the packing list
Spread rateWritten per jointBench check at set-up
Open timeSeason-adjustedTimer on the bench
Clamp pressureSpecified per fixtureRegulator + gauge
UnclampOn timerInspector releases the rack

Glue process control

Corner blocks do the quiet work

Every rail junction gets a glued corner block screwed both directions. They are invisible in the catalogue photos and they are why a frame survives being dragged across a restaurant floor sideways.

A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.

Season and shop humidity

Winter glue batches run in drier shops and summer runs in humid ones; open time and cure change with both. The workshop adjusts the spread and the clamp schedule with the season instead of pretending it does not matter.

A dining chair usually goes into a heated room and sits at 6 to 8 percent for months. Built at 12 percent, the rails shrink and the joints open; built at 8, it is stable. The band is chosen for the market, not for the kiln.

What the inspector looks for

Squeeze-out the width of a thread, uniform, and gone after sanding. Heavy squeeze-out means too much spread; none means a dry joint.

Domestic seating is tested under EN 12520 — seat and back fatigue, a leg forward load and a stability check. Light contract use moves to EN 16139 Level 1, which cycles the frame considerably harder.

The returns are front leg joints loosening, seats splitting at the end grain where the finish did not cover it, and rocking from a frame machined out of tolerance. All three are visible in the first month, not the fifth year.

Questions

What glue do you use?

A D4-class PVA for interior service, and a structural adhesive where the design asks for it; the choice is written into the specification of each dining chair.

Is glue harmful after curing?

Cured PVA is inert; our finishes carry the emission documentation buyers usually ask for on solid wood dining chairs projects.

Why did a joint on my sample open?

Nine times out of ten the timber was too wet at assembly, which is why every batch ships with the moisture record.

Can you glue and screw everything?

We glue structural joints and reserve screws for serviceable parts; all-glued frames are harder to repair and all-screwed frames creep.