Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Bar Stools

Glue, Clamp Time and Corner Blocks on Bar Stools

Moisture, spread, open time and clamp pressure - the four controls that turn glue from a bottle into a process on bar stools.

Updated 2026-10-17Longjiang, Foshan11 min read

Moisture, spread, open time and clamp pressure - the four controls that turn glue from a bottle into a process on bar stools.

These notes come off the production floor in Longjiang, Foshan. The current wholesale wooden bar stools range is on the main site, with a specification page for every model in it.

Glue is a process, not a bottle

The adhesive matters less than the four things around it: moisture of the timber, spread rate, open time and clamp pressure. On a bar stool line those four are written down and checked, because they are the difference between a glue line and a glue film.

Assembly runs vertically: seat mount first, then the footring, then the seat. Clamping a stool square is harder than clamping a chair because the column gives you nothing to reference against — the jig does the work.

Clamp time is not negotiable

Parts come off the clamp bench on a timer, not on feel. A bar stool frame unclamped early holds its shape for a day and walks for a year - the rail drifts out of square and the seat deck never sits flat again.

A stool column is a thick section and a footring is a bent one, and both come out of the same charge as thinner seat blanks. That is exactly the case where one schedule delivers two moisture contents, so the thick stock is dried separately.

Control pointTargetVerification
Timber moisture8-12%Meter per batch, on the packing list
Spread rateWritten per jointBench check at set-up
Open timeSeason-adjustedTimer on the bench
Clamp pressureSpecified per fixtureRegulator + gauge
UnclampOn timerInspector releases the rack

Glue process control

Corner blocks do the quiet work

Every rail junction gets a glued corner block screwed both directions. They are invisible in the catalogue photos and they are why a frame survives being dragged across a restaurant floor sideways.

A stool carries its load differently from a chair. The seat is high, the base is narrow relative to the height, and the footring takes a sideways kick every time someone climbs on or pushes off. That is why the ring on our stools is a welded closed section joined to the column, not a ring screwed into a leg.

Season and shop humidity

Winter glue batches run in drier shops and summer runs in humid ones; open time and cure change with both. The workshop adjusts the spread and the clamp schedule with the season instead of pretending it does not matter.

Stool columns are thick and they respond slowly to a change in humidity, which helps: a column that arrives at 10 percent will not fall to 6 percent in a week. The seat, at 25 mm, will. That mismatch inside one product is why components are metered separately.

What the inspector looks for

Squeeze-out the width of a thread, uniform, and gone after sanding. Heavy squeeze-out means too much spread; none means a dry joint.

Beyond the frame test a stool gets a stability check at height and a footring load test: push the ring sideways with the stool loaded and it must not deform. Swivel models are cycled, not just sat on.

The three returns we see: footring welds cracking after a season, swivel mechanisms that lose their gas, and seat pads compressed flat at the front edge. All three are specifiable — a closed-section ring, a contract-rated lift, and a 35 kg/m³ foam.

Questions

What glue do you use?

A D4-class PVA for interior service, and a structural adhesive where the design asks for it; the choice is written into the specification of each bar stool.

Is glue harmful after curing?

Cured PVA is inert; our finishes carry the emission documentation buyers usually ask for on wooden bar stools projects.

Why did a joint on my sample open?

Nine times out of ten the timber was too wet at assembly, which is why every batch ships with the moisture record.

Can you glue and screw everything?

We glue structural joints and reserve screws for serviceable parts; all-glued frames are harder to repair and all-screwed frames creep.