Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Solid Wood Dining Chairs

Ash or Rubberwood for Dining Chairs: Choosing the Timber

Hardness, grain, movement and cost - how to choose between ash and rubberwood for a dining chair order.

Updated 2026-10-16Longjiang, Foshan11 min read

Hardness, grain, movement and cost - how to choose between ash and rubberwood for a dining chair order.

These notes come off the production floor in Longjiang, Foshan. The current wholesale solid wood dining chairs range is on the main site, with a specification page for every model in it.

Two timbers, two different contracts

Ash and rubberwood dominate this category, and they are not interchangeable. Ash brings hardness and an open grain that takes stain beautifully; rubberwood brings cost control and a tight, even grain.

Around 70% of what we run is ash and roughly 30% rubberwood, and both appear in this category's charge book. Ash dries steadily and holds its colour; rubberwood dries fast and evenly. Both are metered the same way.

Hardness and service life

Ash takes a beating - legs and rails in hard service stay honest. Rubberwood is softer under the knife and under use, which is why frame details are chunkier when it is specified.

A dining chair is a four-legged frame that takes almost its entire load through the two front legs when someone sits down hard or pushes back from a table. The front leg to side rail joint is the one that decides whether the chair is tight after five years. We cut it as a mortise and tenon with a corner block.

PropertyAshRubberwood
HardnessHighModerate
GrainOpen, striking under stainTight, uniform
MovementManaged by kiln + designManaged by design
CostHigherLower
Typical useStained, hard servicePainted, volume orders

Ash vs rubberwood

Stability in humid rooms

Both are kiln-dried to the same 8-12% band; their movement in service still differs, and joint details are adjusted per species rather than copied.

Seat rails at 20 to 25 mm and legs at 42 to 50 mm do not dry at the same rate. Running them through one charge is the standard shortcut that produces a frame whose rails move after assembly, so we group by section rather than by order.

Seat rails are tenoned into the legs and the corner block is both glued and screwed. Screws alone work for a year; a glued block carries the racking load that a dining chair lives with. Turn the chair over and you can see the difference.

How they look after finishing

Open grain after a stain has depth; tight grain reads cleaner and more uniform. Colour panels are signed per species because the same stain is not the same colour on both.

The seat is the surface people touch and see. A solid wood seat is sanded to a finer grit than the frame and the end grain is sealed, because a seat splits from the end outwards. Frames get the standard three-grit sequence.

Choosing between them for your project

Hard service and stained looks lean ash; budget-driven volume leans rubberwood. The solid wood dining chairs range carries both, and the specification sheet says which is which.

Home dining rooms, apartments and showrooms. Seat height 450 to 470 mm against a 720 to 750 mm table, seat depth 400 to 450 mm. Standard is domestic use under EN 12520, with EN 16139 Level 1 available where the chairs go into a serviced space.

Current solid wood dining chairs references: A0010 (100% Wood, MOQ 4 pcs), A005 (Solid wood/Leather, MOQ 6 pcs), A009 (100% Solid Wood, MOQ 6 pcs).

Questions

Which timber should I pick for dining chairs?

Tell us the venue and the finish; hard service and stained work lean ash, budget volume leans rubberwood.

Is rubberwood a 'cheap' wood?

It is a managed plantation timber with different properties, not a worse one - the design compensates where it must.

Do both ship with moisture records?

Yes, 8-12% band, meter per batch, printed on the packing list.

Can I mix species in one order?

Yes, with per-species colour panels; the two take the same stain differently.