Guangdong Chair Factory Notes Production floor, Longjiang · Foshan

Factory Notes › Wooden Dining Armchairs

Ash or Rubberwood for Dining Armchairs: Choosing the Timber

Hardness, grain, movement and cost - how to choose between ash and rubberwood for a dining armchair order.

Updated 2026-10-16Longjiang, Foshan11 min read

Hardness, grain, movement and cost - how to choose between ash and rubberwood for a dining armchair order.

These notes come off the production floor in Longjiang, Foshan. The current wholesale wooden dining armchairs range is on the main site, with a specification page for every model in it.

Two timbers, two different contracts

Ash and rubberwood dominate this category, and they are not interchangeable. Ash brings hardness and an open grain that takes stain beautifully; rubberwood brings cost control and a tight, even grain.

Arms are nearly always ash, because a shaped arm needs a timber that holds a curve and takes a knock; rubberwood marks too readily for a surface people grab. Most of the charge in this category is ash for that reason.

Hardness and service life

Ash takes a beating - legs and rails in hard service stay honest. Rubberwood is softer under the knife and under use, which is why frame details are chunkier when it is specified.

An armchair is a dining chair with a lever attached. The arm is a cantilever: every time someone pushes themselves up, the load goes through the arm into the back post and out into the rear leg. That is the joint we reinforce, and it is why an armchair is heavier than the side chair it matches.

PropertyAshRubberwood
HardnessHighModerate
GrainOpen, striking under stainTight, uniform
MovementManaged by kiln + designManaged by design
CostHigherLower
Typical useStained, hard servicePainted, volume orders

Ash vs rubberwood

Stability in humid rooms

Both are kiln-dried to the same 8-12% band; their movement in service still differs, and joint details are adjusted per species rather than copied.

Arm stock at 35 to 45 mm is the thickest material in this category and the slowest to dry. Push it and you get checking inside the arm, invisible under finish, and the arm later fails at the joint rather than in the middle.

Arms are tenoned into the back post and through-bolted where the section allows. The arm to post joint failing is the single most common armchair return in the industry, and it is a specification problem, not a manufacturing one.

How they look after finishing

Open grain after a stain has depth; tight grain reads cleaner and more uniform. Colour panels are signed per species because the same stain is not the same colour on both.

Arms are handled constantly and show wear first, so the top face and the front end take an extra pass and the finish is built slightly higher there. The underside of the arm is finished too — it is at eye level for anyone sitting beside it.

Choosing between them for your project

Hard service and stained looks lean ash; budget-driven volume leans rubberwood. The wooden dining armchairs range carries both, and the specification sheet says which is which.

Head of table, banquets, clubs and hotel suites. Arm height matters as much as seat height: if the arm will not pass under the table apron, the chair cannot be pushed in and it blocks the room. Measure the apron before you order.

Current wooden dining armchairs references: A0017 (100% Wood, MOQ 4 pcs), A005 (solid wood, MOQ 2 pcs), XY-24018 (Solid wood, MOQ 6 pcs).

Questions

Which timber should I pick for dining armchairs?

Tell us the venue and the finish; hard service and stained work lean ash, budget volume leans rubberwood.

Is rubberwood a 'cheap' wood?

It is a managed plantation timber with different properties, not a worse one - the design compensates where it must.

Do both ship with moisture records?

Yes, 8-12% band, meter per batch, printed on the packing list.

Can I mix species in one order?

Yes, with per-species colour panels; the two take the same stain differently.